Multitech MMCModem GPRS Reference Manual Download Page 188

Page: 188 / 203

Appendix C – Structure of the Terminal Profile

Multi-Tech Systems, Inc. Wireless GSM/GPRS AT Commands (Document Number S000293I)

188

Appendix C – Structure of the

Terminal Profile

First byte (Download):
b8 b7 b6 b5 b4 b3 b2 b1

Profile

download

User choice

SMS-PP

data

download

Set by product to 1

Cell

Broadcast

data

download

Set by product to 1

selection

User choice

'9E

XX'

response

code

for

SIM

data

download error

Set by product to 1

Timer expiration

Set by product to 0

USSD

string

data

object

supported

Call Control

User choice

RFU, bit=0

Second byte (Other):
b8 b7 b6 b5 b4 b3 b2 b1

Command

result

User choice

Call Control by SIM

User choice

Cell

identity

included

Call

Control

by SIM

User choice

MO short message control by SIM

User choice

Handling

the

alpha

identifier

according to subclause 9.1.3

User choice

UCS2 Entry supported

User choice

UCS2

Display

supported

User choice

Display

the

extension

text

User choice

Third byte (Proactive SIM):
b8 b7 b6 b5 b4 b3 b2 b1

Proactive

SIM:

DISPLAY

TEXT

User choice

Proactive

SIM:

GET

INKEY

User choice

Proactive SIM: GET INPUT

User choice

Proactive SIM: MORE TIME

User choice

Proactive SIM: PLAY TONE

User choice

Proactive

SIM:

POLL

INTERVAL

Set by product to 1

Proactive SIM: POLLING OFF

Set by product to 1

Proactive

SIM:

REFRESH

User choice

Fourth byte (Proactive SIM):
b8 b7 b6 b5 b4 b3 b2 b1

Proactive

SIM:

SELECT

ITEM

User choice

Proactive

SIM:

SEND

SHORT

MESSAGE

User choice

Proactive

SIM:

SEND

User choice

Proactive

SIM:

SEND

USSD

User choice

Proactive

SIM:

SET

CALL

User choice

Proactive

SIM:

SET

User choice

Proactive SIM: PROVIDE LOCAL
INFORMATION (MCC, MNC, LAC,
Cell ID & IMEI)

Set by product to 1

Proactive SIM: PROVIDE LOCAL
INFORMATION (NMR)

Set by product to 1

Summary of Contents for MMCModem GPRS












































































































































































































Search results

Summary of Contents for MMCModem GPRS

Reviews:

Related manuals for MMCModem GPRS

Brands by name

Popular brands

Multitech MMCModem GPRS, Reference Manual

Search results

Summary of Contents for MMCModem GPRS

Reviews:

Related manuals for MMCModem GPRS

Brands by name

Popular brands