Multitech MMCModem GPRS Reference Manual Download Page 175

Page: 175 / 203

Appendix A – Result Codes, Failure Causes, Other Tables

Multi-Tech Systems, Inc. Wireless GSM/GPRS AT Commands (Document Number S000293I)

175

Continued: Specific Error Result Codes

<error> Meaning

Results from the following commands

544

CMUX connection Timeout (no answer from the remote); i.e., no
DLCO opened response.

+CMUX

545

A CMUX session has been started on a physical UART, and the
user tries to start another CMUX session on another physical
UART. The error, +CME ERROR: 545 is raised on the UART
where AT+CMUX command is trying to be started again.

+CMUX

546

Emergency call is not allowed without SIM

+COPS

547

Emergency call is allowed without SIM

+COPS

548

No flash objects to delete

+WOPEN

549

The phone number of the requested phonebook entry is empty

ATD><index>[;],ATD><phonebook><index>[;]

550

Unable to resize the Application & Data storage place since the
new required size would overlap with the current Open AT

application storage place

+WOPEN

551

Service abort request has failed

AT+WAC

552

Unsolicited responses for autodiag or charge indication are
already activated on another port

+WDIAG, +WBCM

Summary of Contents for MMCModem GPRS












































































































































































































Search results

Summary of Contents for MMCModem GPRS

Reviews:

Related manuals for MMCModem GPRS

Brands by name

Popular brands

Multitech MMCModem GPRS, Reference Manual

Search results

Summary of Contents for MMCModem GPRS

Reviews:

Related manuals for MMCModem GPRS

Brands by name

Popular brands