REGULATORY & SAFETY INFORMATION
Conduit
®
300 Series IoT Programmable Gateway MTCDT3AC-L4G1/-EN Hardware Guide
29
Rule Parts
Frequency Range
Output Watts
Frequency Tolerance Emission Designator
27
782.0 - 782.0
0.4217
0.1 PPM
8M91G7D
27
782.0 - 782.0
0.2911
0.1 PPM
8M91W7D
27
779.5 - 784.5
0.4395
0.1 PPM
4M48G7D
27
779.5 - 784.5
0.309
0.1 PPM
4M49W7D
24E
1860.0 - 1905.0
0.3516
0.1 PPM
17M9G7D
24E
1860.0 - 1905.0
0.2489
0.1 PPM
17M9W7D
24E
1855.0 - 1910.0
0.4111
0.1 PPM
8M91G7D
24E
1850.7 - 1914.3
0.2429
0.1 PPM
1M09W7D
90
819.0 - 819.0
0.2198
0.1 PPM
8M91G7D
90
819.0 - 819.0
0.1738
0.1 PPM
8M91W7D
90
814.7 - 823.3
0.2455
0.1 PPM
1M09G7D
90
814.7 - 823.3
0.1972
0.1 PPM
1M09W7D
22H
831.5 - 841.5
0.2582
0.1 PPM
13M5G7D
22H
831.5 - 841.5
0.1828
0.1 PPM
13M4W7D
22H
826.5 - 846.5
0.1945
0.1 PPM
4M49W7D
27
2580.0 - 2610.0
0.3926
0.1 PPM
17M8G7D
27
2580.0 - 2610.0
0.2799
0.1 PPM
17M8W7D
27
2575.0 - 2615.0
0.3936
0.1 PPM
8M91G7D
27
2506.0 - 2680.0
0.4842
0.1 PPM
17M9G7D
27
2506.0 - 2680.0
0.342
0.1 PPM
17M9W7D
27
2501.0 - 2685.0
0.4853
0.1 PPM
8M91G7D
27
2498.5 - 2687.5
0.3451
0.1 PPM
4M50W7D
Single Modular Approval. Power listed is ERP for part 22 and part 27 below 1 GHz, EIRP for part 24 and part 27
above 1 GHz. Approval is limited to OEM installation only. Compliance of this device in all final host configurations
is the responsibility of the Grantee. This device is to be used only for mobile and fixed applications. OEM
integrators must be provided labeling requirements for finished products. This grant is valid only when the device
is sold to OEM integrators and the OEM integrators are instructed to ensure that the end user has no manual
instructions to remove or install the device. Separate approval is required for all other operating configurations,
including portable configurations with respect to 2.1093 and different antenna configurations. The module
antenna(s) must be installed to meet the RF exposure compliance separation distance of 20 cm and any additional
testing and authorization process as required. Co-location of this module with other transmitters that operate
simultaneously are required to be evaluated using the FCC multi-transmitter procedures. The antenna installation
and operating configurations of this transmitter, including any applicable source-based time-averaging duty factor,
antenna gain, and cable loss must satisfy MPE categorical Exclusion Requirements of Part 2.1091. Users must be
provided with instructions and transmitter operating conditions for satisfying RF exposure compliance. RF exposure
compliance may need to be addressed at the time of licensing, as required by the responsible FCC bureau(s),
including antenna co-location requirements of Part 1.1307(b)(3). This module can only be used with a host antenna
circuit trace layout design in strict compliance with the OEM instructions provided. This device supports: LTE of 1.4,
