MultiTable Manual ModTable Assembly Instructions Manual Download Page 4

Page 4  |  

ModTable

  |  v

s 5.0 

2.0  Safety Information 
2.1 Transport and Assembly

 

To ensure your safety and protect your ModTable it must be moved by at least two people.

Do not drag or pull the ModTable Base across the floor.

Use the tools supplied to assemble the ModTable.

2.2 Use of the ModTable Base 

Do not allow children under the age of 16 to use or assemble the ModTable Base
unsupervised.

Do not use the ModTable Base on an uneven surface.

The ModTable is made for stationary use only, unless you have purchased the Wheel Kit.

2.3 Table Top Limitations 

Below are the minimum and maximum table top dimensions allowed for the ModTable Base:

Without Wheel Kit: 

Minimum Table Top Dimensions: W 24” x L 40”

 

Maximum Table Top Dimensions: W 36” x L 72” 

With Wheel Kit:   

Minimum Table Top Dimensions: W 24” x L 40”

 

Maximum Table Top Dimensions: W 30” x L 60” 

2.4 Specific Dangers 

When assembling your ModTable Base, ensure that you have plenty of room around the base
to avoid collisions.

2.5 Maintenance and Upkeep 

Your new ModTable Base and its components are low maintenance items, but still require
regular maintenance. We recommend checking and tightening the bolts and set screws every
6 months to ensure your table raises and lowers correctly.

Should your base or other components require repairs, please contact us. Any repairs or
alterations should only completed using approved replacement parts from MultiTable.
Replacement parts are available for both in and outside of the warranty time frame.

To clean your ModTable Base and Top, use a clean damp cloth and a mild household cleaning
solution.

IMPORTANT! 

Stop using the ModTable at once if you notice anything unusual.

Contact MultiTable customer service at 602.773.6911, or [email protected].

Summary of Contents for Manual ModTable
















Reviews: