MULTIQUIP UWKB, Instructions

Page: 2 / 4

UWKB — Wheel Kit instrUctions p/n UWKB01 — rev. #0 (02/03/12) — page 2
3.„ Set„the„rounded„corner„of„the„tubing„in„the„bracket„at„
the„back„of„the„axle„mount„and„place„a„screw„(item„5)„
and„flat„washer„(item„6)„through„the„holes,„securing„
the„tubing„in„place.„Place„another„flat„washer„and„a„
nyloc„nut„(item„7)„on„the„threaded„end„of„the„screw„
and„tighten.
4.„ Secure„the„axle„mount„to„the„frame„tubing„by„placing„
a„small„clamp„(item„8)„over„the„frame„tubing„and„the„
axle„mount.„Place„a„large„clamp„(item„9)„over„the„small„
clamp.„Insert„screw„(item„18)„into„the„small„clamp„and„
secure„with„nyloc„nut„(item„7)„and„washer„(item„6).„
Tighten„screw„until„the„clamp„securely„holds„the„axle„
mount„to„the„frame„tubing.
5.„ Repeat„steps„2„through„4„to„attach„the„axle„mount„to„
the„opposite„side„of„the„unit.
6.„ Insert„a„flat„washer„(item„16)„into„the„crutch„tip„(item„17)„
and„place„the„combined„items„over„the„open„end„of„
the„handle„mount„(item„15).„See„Figure„3.
Figure 3. Handle Mount Assembly
7.„ Insert„the„end„of„the„handle„tube„(item„13)„with„the„
screw„hole„into„the„top„bracket„of„the„handle„mount.„
Slide„a„clevis„pin„(item„10)„and„flat„washer„(item„11)„
through„ the„ bracket„ and„ handle„ tube„ holes.„ Place„
another„flat„washer„on„the„end„of„the„clevis„pin.„Insert„
a„cotter„pin„(item„12)„through„the„hole„in„the„clevis„pin„
to„secure„the„handle„tube„to„the„handle„mount.
8.„ Slide„the„hand„grip„(item„14)„over„the„open„end„of„the„
handle„tube.
NOTICE
Attach„the„axle„mounts„so„that„the„wheels„are„located„
under„the„heaviest„end„of„your„unit.„The„placement„of„
the„axle„mounts„may„differ„on„each„type„of„equipment.
9.„ Lifting„the„front„of„the„unit,„set„the„rounded„corner„of„
the„frame„tubing„into„the„support„bracket„on„the„handle„
mount„ (Figure„ 4).„ Secure„ the„ handle„ mount„ to„ the„
frame„tubing„by„placing„a„large„clamp„(item„9)„around„
the„frame„tubing„and„the„handle„mount.„See„Figure„4.
Figure 4. Securing Handle Mount to the Frame
10.„ Insert„the„small„clamp„(item„8)„on„the„other„side„of„the„
handle„mount„and„frame„tubing,„so„that„the„large„and„
small„clamps„are„facing„each„other.
11.„ Insert„screw„(item„18)„into„small„clamp„and„secure„
with„nyloc„nuts„(item„7).„Tighten„screw„until„the„clamp„
securely„holds„the„handle„mount„to„the„frame„tubing.
12.„ Repeat„steps„9„through„11„to„attach„the„handle„mount„
to„the„other„side„of„the„unit.
7
LARGE
CLAMP
SMALL
CLAMP
8
18
PUMP
FRAME
9
6
HANDLE
MOUNT
6