background image

QP4TH TRASH PUMP • OPERATION AND PARTS MANUAL — REV. #3 (01/29/14) — PAGE 15

6. 

Choke Lever —

 

Used in the starting of a cold engine, 

or in cold weather conditions. The choke enriches the 

fuel mixture.

7. 

Air Cleaner — Prevents dirt and other debris from 

entering the fuel system. Remove wing-nut on top of 

air filter cannister to gain access to filter element. 

8. 

Spark Plug — Provides spark to the ignition system. 

Set spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch). 

Clean spark plug once a week.

9. 

Muffler —

 

Used to reduce noise and emissions.

10. 

Fuel Tank —

 

Holds unleaded gasoline. For additional 

information refer to engine owner's manual. 

 NOTICE

Operating the engine without an air filter, with a 

damaged air filter, or a filter in need of replacement 

will allow dirt to enter the engine, causing rapid engine 

wear.

  WARNING

Engine components can generate 

extreme heat. To prevent burns,

  

DO NOT touch these areas while the 

engine is running or immediately after 

operating. 

NEVER operate the engine 

with the muffler removed.

Figure 4. Engine Controls and Components

INITIAL SERVICING

The engine (See Figure 4) must be checked for proper 

lubrication and filled with fuel prior to operation. Refer to the 

manufacturers engine manual for instructions and details 

of operation and servicing. The engine shown above is a 

HONDA engine, operation for other types of engines may 

vary somewhat.
1. 

Fuel Filler Cap —

 

Remove this cap to add unleaded 

gasoline to the fuel tank. Make sure cap is tightened 

securely. 

DO NOT over fill.

2. 

Throttle Lever —

 

Used to adjust engine RPM speed 

(lever advanced forward 

SLOW

, lever back toward 

operator 

FAST

).

3. 

Engine ON/OFF Switch —

 

ON position permits engine 

starting, OFF position stops engine operations.

4. 

Recoil Starter (pull rope) —

 

Manual-starting method. 

Pull the starter grip until resistance is felt, then pull 

briskly and smoothly.

5. 

Fuel Valve Lever — OPEN to let fuel flow, CLOSE to 

stop the flow of fuel.

  DANGER

Adding fuel to the tank should be done 

only when the engine is stopped and has 

had an opportunity to cool down. In the 

event of a fuel spill, 

DO NOT attempt to 

start the engine until the fuel residue has 

been completely wiped up, and the area 

surrounding the engine is dry. 

BASIC ENGINE

Summary of Contents for QP4TH







































Reviews: