background image

DCa70USI2 60 hz generaTor • operaTIon anD parTS manUal — rev. #0 (06/28/11) — page 49

trOuBleshOOting (diagnOstic laMp)

The engine controller of this generator diagnoses problems 

that arise from the engine control system and the engine 

itself.  Press  the  diagnostic  button  (Figure  66)  on  the 

diagnostic panel to determine if an engine malfunction has 

occurred.

Figure 66. Diagnostic Panel

meThoD oF operaTIon

1.  Normally, the diagnostic lamp will be 

dimly lit when 

the 

mpeC Control Switch is placed in the manUal 

position.

2.  If engine trouble occurs, the diagnostic lamp will be 

brightly lit as long as the control switch is left in the 

manual position.

3.  The  diagnostic  lamp  will  indicate  that  an  engine 

malfunction has occurred.

 NOTICE

For  a  complete  understanding  of  error  codes  and 

troubleshooting  procedures,  refer  to  the  enclosed 

engine instruction manual.

 NOTICE

If the engine is cranked while the diagnostic switch is in 

the “

on” position, the engine will not be stopped even if 

the starter switch is turned to the “

oFF” position. In such 

case, turn the diagnostic switch to the “

oFF” position.

Summary of Contents for Power WHISPERWATT DCA70USI2





















































































Reviews: