background image

PAGE 44 — DCA-70USJ —  OPERATION AND PARTS  MANUAL — REV. #0  (09/16/04)

Trailer Maintenance

This section is intended to provide the user with generic
trailer service and maintenance information. The service and
maintenance guidelines referenced in this section refer to a
wide range of trailers.

Remember periodic inspection of the trailer will ensure safe
towing of the generator and will prevent personal injury and
damage to the equipment.

The definitions below describe some of the major components
of a typical trailer that would be used with the DCA-70USJ
Ultra-Silent Generator.

1.

Fuel Cell -

 Provides an adequate amount of fuel for the

equipment in use. Fuel cells must be empty when trans-
porting equipment.

2.

Braking System 

- System employed in stopping the

trailer. Typical braking systems are electric, surge, hy-
draulic, hydraulic-surge and air.

3.

GVWR- 

Gross Vehicle Weight Rating (GVWR) is the

maximum number of pounds the trailer can carry, in-
cluding the fuel cell (empty).

4.

Frame Length - 

Measurement is from the ball hitch to

the rear bumper (reflector).

5.

Frame Width - 

 Measurement is from fender to fender

6.

Jack Stand - 

 Trailer support device with maximum pound

requirement from the tongue of the trailer.

7.

Coupler - 

Type of hitch used on the trailer for towing.

8.

Tire Size - 

Indicates the diameter of the tire in inches

(10,12,14, etc.), and the width in millimeters
(175,185,205, etc.).  The tire diameter must match the
diameter of the tire rim.

9.

Tire Ply - 

The tire ply (layers) number is rated in letters;

2-ply,4-ply,6-ply, etc.

10.

Wheel Hub - 

The wheel hub is connected to the trailer’s

axle.

11.

Tire Rim - 

Tires mounted on a tire rim.  The tire rim must

match the size of the tire.

12.

Lug Nuts - 

Used to secure the wheel to the wheel hub.

Always use a torque wrench to tighten down the lug
nuts.  See Table 17 and Figure 59

 

for lug nut tightening

and sequence.

13.

Axle -

 Indicates the maximum weight the axle can sup-

port in pounds, and the diameter of the axle expressed
in inches.  Please note that some trailers have a double
axle.  This will be shown as 2-6000 lbs., meaning two
axles with a total weight capacity of 6000 pounds.

14.

Suspension - 

Protects the trailer chassis from shocks

transmitted through the wheels.  Types of suspension
used are leaf, Q-flex, and air ride.

15.

Electrical -

 Electrical connectors (looms) are provided

with the trailer so the brake lights and turn signals can
be connected to the towing vehicle.

16.

Application - 

Indicates which units can be employed

on a particular trailer.

DCA-70USJ — TRAILER MAINTENANCE

Summary of Contents for Power Ultra-Silent DCA-70USJ























































































Reviews: