background image

PAGE 30 — MQP56 60 HZ GENERATOR • OPERATION MANUAL — REV. #0 (06/14/17) 

INSPECTION/SETUP

CIRCUIT BREAKERS

To protect the generator from an overload, a 3-pole, 175 

amp, main circuit breaker is provided to protect the 

U,V, 

and W Output Terminals

 from overload. In addition, two 

single-pole, 20 amp 

duplex 

circuit breakers are provided 

to protect the GFCI receptacles from overload. Three 50 

amp 

load

 circuit breakers have also been provided to 

protect the auxiliary receptacles from overload. Make sure 

to switch 

ALL

 circuit breakers to the 

OFF

 position prior to 

starting the engine.

LUBRICATION OIL

Fill the engine crankcase with lubricating oil through the 

filler hole, but 

DO NOT

 overfill. Make sure the generator is 

level and verify that the oil level is maintained between the 

two notches (Figure 28) on the dipstick. See Table 11 for 

proper selection of engine oil.

Figure 28. Engine Oil Dipstick

When checking the engine oil, be sure to check if the oil is 

clean. If the oil is not clean, drain the oil by removing the oil 

drain plug and opening drain valve. Refill with the specified 

amount of oil as outlined in the 

ISUZU Engine Owner’s 

Manual

. Oil should be warm before draining.

Other types of motor oils may be substituted if they meet 

the following requirements:

 

„

 API Service Classification CC/SC

 

„

API Service Classification CC/SD

 

„

API Service Classification CC/SE

 

„

API Service Classification CC/SF

Table 11. Recommended Motor Oil

FUEL CHECK

Refilling the Fuel System 

This generator has an internal fuel tank located inside the 

generator enclosure (Figure 29). 

ALWAYS

 fill the fuel tanks 

with clean fresh 

#2 diesel fuel. DO NOT

 fill the fuel tanks 

beyond their capacities.
Pay attention to the fuel tank capacity when replenishing 

fuel. The fuel tank cap must be closed tightly after filling. 

Handle fuel in a safety container. If the container does not 

have a spout, use a funnel. Wipe up any spilled fuel 

immediately.

Figure 29. Internal Fuel Tank System

  DANGER

Fuel spillage on a 

hot

 engine can cause 

fire

 or 

explosion

. If fuel spillage occurs, 

wipe up the spilled fuel completely to 

prevent fire hazards. 

NEVER

 smoke 

around or near the generator. Make sure 

engine is 

OFF

 before refueling.

  CAUTION

ONLY properly trained personnel

 who have read 

and understand this section should refill the fuel tank 

system.

INTERNAL

FUEL TANK

NOTICE

DO NOT

 add fuel while engine is running. Stop engine 

and let cool before adding fuel. 

Summary of Contents for MQP56





















































Reviews: