background image

page 40 — Sg1400C3 STudio generaTor • operaTion manual — rev. #0 (10/05/11) 

Fuel TanK inSpeCTion

In  addition  to  cleaning  the  fuel  tank,  the  following 

components should be inspected for wear:

 

„

rubber  Suspension  —  look  for  signs  of  wear  or 

deformity due to contact with oil. Replace the rubber 

suspension if necessary.

 

„

Fuel Hoses — inspect nylon and rubber hoses for signs 

of wear, deterioration, and hardening.

 

„

Fuel Tank lining — inspect the fuel tank lining for signs 

of excessive amounts of oil and other foreign matter.

replacing Fuel Filter

 

„

Replace the fuel filter cartridge with a new one every 

500 hours.

 

„

Loosen the drain plug at the lower top of the fuel filter. 

Drain the fuel in the fuel body together with the mixed 

water. 

do noT spill the fuel during disassembly.

 

„

Vent any air.

air removal

If air enters the fuel injection system of a diesel engine, 

starting becomes impossible. After running out of fuel, or 

after  disassembling  the  fuel  system,  bleed  the  system. 

Refer to the Cummins engine manual for details.

CHeCK oil level

Check the crankcase oil level prior to each use, or when 

the  fuel  tank  is  filled.  Insufficient  oil  may  cause  severe 

damage to the engine. The oil level must be between the 

two notches on the dipstick.

replacing oil Filter

1.  Remove the old oil filter.
2.  Apply a film of oil to the gasket on the new oil filter.
3.  Install the new oil filter.
4.  After the oil filter has been replaced, the engine oil will 

drop slightly. Run the engine for a while and check for 

leaks before adding more oil if needed. Clean excessive 

oil from engine.

MaintEnanCE

FluSHing  ouT  radiaTor  and  replaCing 

CoolanT

1.  Remove  radiator  cap.  Remove  coolant  drain  plug 

located on side of generator. Place coolant drain lever 

in the open position to drain coolant.

2.  Flush the radiator by running clean tap water through 

radiator until signs of rust and dirt are removed. Do 

not clean radiator core with any objects, such as a 

screwdriver.

3.  Check hoses for softening and kinks. Check clamps 

for signs of leakage.

4.  Move lever to the closed position and reinstall coolant 

drain plug.

5.  Replace with coolant as recommended by the engine 

manufacturer.

6.  Close radiator cap tightly.

generaTor STorage

For  long  term  storage  of  the  generator  the  following  is 

recommended:
1.  Drain the fuel tank completely. Treat with a fuel stabilizer 

if necessary.

2.  Completely drain the oil from the crankcase and refill, 

if necessary, with fresh oil.

3.  Clean the entire generator, inside and outside.
4.  Disconnect the battery.
5.  Make sure engine coolant is at proper level.
6.  Cover the generator and store in a clean, and dry place.

  Warning

Allow engine to 

cool before flushing out 

radiator.  Flushing  the  radiator  while  hot 

could cause serious burns from water or 

steam.

Summary of Contents for MQ POWER SG1400C3































































Reviews: