MULTIQUIP MC12PH Operation And Parts Manual Download Page 21

Page: 21 / 79

PAGE 20 — MC12PH CONCRETE MIXER • OPERATION AND PARTS MANUAL — REV. #1 (09/02/15)

V-BELT CHECK

Visually examine the V-belt (Figure 6) and determine if it

is full of tiny cracks, frayed, has pieces of rubber missing,

is peeling or otherwise damaged.
Also, examine the belt and determine if it is

oil soaked

glazed

" (hard shiny appearance on the sides of the belt).

Either of these two conditions can cause the belt to run hot,

which can weaken it and increase the danger of it breaking.
If the V-belt exhibits any of the above wear conditions

replace the V-belt immediately.

Figure 6. V-Belt Inspection

START/STOP SWITCH

This unit has been equipped with a start/stop switch

(Figure 7), which should be tested every time the unit is

started.

Figure 7. Start/Stop Switch

GLAZED

OIL SOAKED

BROKEN

CORD FAILURE

CRACKS

MISSING RUBBER

SIDEWALL

WEAR

WORN BACK

COVER

PULL OUT

TO START ENGINE

PUSH IN

TO STOP ENGINE

START/STOP

SWITCH

INSPECTION

Discount-Equipment.com

Summary of Contents for MC12PH
















































































Search results

Summary of Contents for MC12PH

Reviews:

Related manuals for MC12PH

Brands by name

Popular brands

MULTIQUIP MC12PH, Operation And Parts Manual

Search results

Summary of Contents for MC12PH

Reviews:

Related manuals for MC12PH

Brands by name

Popular brands