Operating Instructions
PERMAX BL-O 3720-0630 – brushless outrunner motor
!
These operating instructions are an integral part of this
product. They contain important information and safety
notes, and should be kept in a safe place at all times. Be
sure to pass them on to the new owner if you ever dispose
of the product.
1. I
NTRODUCTION
PERMAX motors are manufactured to high standards for quality-
conscious modellers. Carefully optimised for low weight, high
efficiency, high torque and durability, PERMAX brushless motors
are the perfect choice as power plants for RC models.
2. S
PECIFICATION
PERMAX BL-3720-06350 brushless motor is designed for use in
3D models with an all-up weight of up to about 1500 g, for
aerobatic models weighing up to about 2400 g and trainers up to
around 4000 g. They also are suitable for powered gliders
weighing up to around 6000 g.
3. S
AFETY
N
OTES
•
Read the instructions before using the motor for the first time
•
Check that the motor and propeller are firmly attached before
every flight
•
Do not connect the battery to the speed controller until you
have switched the RC system on, and checked that the throttle
stick is at the “OFF” position
•
Never run the motor whilst holding it in your hand
•
Do not exceed the stated maximum screw depth when
installing the motor
•
Remove all loose, lightweight objects from the area in front of
the propeller before running the motor, as they may be sucked
into the propeller
•
Protect the motor from dirt and damp
•
Ensure that no foreign bodies get inside the motor
•
When the motor is running, do not stand in front of the
propeller plane or in line with it
•
Do not exceed the maximum permitted rotational speed of the
motor and propeller
•
Stop the motor immediately if you notice vibration, and
eliminate the cause before running it again. You may need to
balance the propeller
•
PERMAX brushless motors must never be connected directly
to a power source, as this will wreck the motor
4. O
PERATING
N
OTES
PERMAX brushless motors must only be run in conjunction with
a sensorless controller for brushless motors. If the motor shaft
spins in the wrong direction, disconnect the battery (to avoid
short-circuits) and swap over any two of the leads between the
motor and the speed controller.
Do not bend the motor leads sharply. Deploy them in such a way
that they are not subjected from vibration and oscillation.
Do not shorten the wires attached to the motor. If you wish to
use different connectors, unsolder the existing ones.
Ensure that the motor and speed controller are adequately
cooled when running. The maximum motor load may only be
used briefly, i.e. no more than fifteen seconds. At the same time
the maximum case temperature of 65°C must not be exceeded.
Use properly balanced propellers only, as this avoids vibration
and premature bearing damage.
5. M
AINTENANCE
N
OTES
Brushless motors are largely maintenance-free, but a little care
will ensure that they last a very long time:
Protect the motor from dust and dirt - especially the ball races.
Soiled bearings may jam, and they will then need to be replaced.
For this reason lubricate the bearings with thin oil at regular
intervals. Do not immerse the motor in water or solvent.
6. G
UARANTEE
Our products are covered by the currently valid statutory
guarantee regulations. If you wish to make a claim under
guarantee, please contact the model shop where you purchased
the product in the first instance.
The guarantee does not cover faults and defects which are
caused by the following errors:
•
Improper operation (e.g. overheating), incorrect connections,
reversed polarity
•
Use of accessories other than genuine MULTIPLEX items
•
Accidental or deliberate damage
•
Faults due to normal wear and tear
•
Operating the motor outside the technical specification
•
Modifications / repairs which were not carried out by
MULTIPLEX or an authorised MULTIPLEX Service Centre
always use our official service for repairs
7.
CE
A
PPROVAL
This product has been assessed in accordance with the
relevant harmonised European directives. You are
therefore the owner of a product whose design fulfils the
protective aims of the European Community relating to the safe
operation of equipment.
You are entitled to see a copy of this Conformity Declaration.
Please contact MULTIPLEX Modellsport GmbH & Co.KG if you
wish to do this.
8. D
ISPOSAL
I
NFORMATION
Electrical equipment marked with the cancelled
waste bin symbol must not be discarded in the
standard household waste; instead it must be taken
to a suitable specialist disposal system.
In the countries of the EU (European Union)
electrical equipment must not be discarded via the normal
domestic refuse system (WEEE - Waste of Electrical and
Electronic Equipment, directive 2002/96/EG). You can take
unwanted equipment to your nearest local authority waste
collection point or recycling centre. There the equipment will be
disposed of correctly and at no cost to you.
By returning your unwanted equipment you can make an
important contribution to the protection of the environment.
Type:
BL-O 3720-0630
#
33 3125
RPM / V:
630
Cell count NiXX / LiPo:
6 - 12 / 2S - 4S
Optimum working range:
37 A – 47 A
Max. current for 15 sec.:
55 A
Shaft Ø:
5,0 mm
Diameter:
37 mm
Length:
46,5 mm
Weight:
151 g
Max. output:
600 W
Max. rotational speed:
15.000 Umin
-1
Max. case temperature:
65
o
C
Mounting:
∅
25 mm / 4 x M3
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de
PER
M
AX B
L
-O
37
20
-063
0 i
ns
tr
uc
ti
ons
(1
3
-10
-16
/BR
AN
)
# 8
2
58
83
E
rr
or
s
and
om
is
s
io
ns
ex
c
e
pt
ed
M
U
L
T
IPL
EX
