background image

      

 

 

 
 
 
              

 

 

MULTI-MOVER XL75

 

 

 

 

 

 

 

 

 

 

 

 

 

17

 

 

Charging may only take place in a well ventilated room.  

 

 

 

Regularly check whether the battery charger stops automatically when the battery is full. 

 

 

Never interrupt the charging process, make sure it is fully completed. 

 

While charging the battery, 

never

 perform repair, cleaning or other work to the Multi-Mover XL75. 

 

Prior to disassembling the batteries, switch off all power consumers, because of the generation of 

sparks. 

 

When disassembling the batteries, first disconnect the mass cable (-)  

When assembling, connect the mass cable as last. 

 

Caution! Always  plus ( + = red) to plus  and minus (- = black) to minus

 

 

Battery fluid is a corrosive acid, avoid contact with clothing, skin and eyes.

  

Immediately wash off possible splashes on clothes or skin with water and soap, then rinse off with 

plenty of water. Possible splashes of acid in the eyes, rinse with clean water for at least 5 minutes 

and immediately consult a doctor. 

  

When the battery is replaced, the old battery should be returned to your dealer or handed in at a le-

gally recognized collection point for batteries. 

 

5.5  Coupling trailer(s) 

 

The Multi-Mover XL75 is made with a standard tow eye with tow pin or a ball coupling point in the 

middle of the Multi-Mover XL75, to which the pole of a trailer can be coupled.  

Maximum slope angle, with / without load  4 / 12 % 

Slowly reverse the Multi-Mover XL75 to the pole of the trailer and place the tow eye or coupling of 

the pole between the tow eyes or coupling point of the Multi-Mover XL75 and insert the tow pin. 

Then secure the tow pin with a spring clip. 

 

Only use the Multi-Mover XL75 if you have thoroughly studied the previous pages and you have no 

more questions.

 

 

 

6            MAINTENANCE

 

 

When performing maintenance, you should always observe the safety regulations, (chapter 3).

 

 

During maintenance, always switch off the Multi-Mover XL75 and remove the ignition key from the 

ignition lock   

In case of doubt, consult the user manual. 

 

6.1 

Inspection

 

The operator should perform the following inspections regularly, without trailer; 

-  

it must be possible to rotate the steering handle (swivel wheel) smoothly to the left and 

right, without jolts  

-  

keep an eye on the wear of driven tyres, if the wheels slip in case of sudden brakes, they will 

Summary of Contents for XL75






















Reviews: