background image

User Manual | MTI 424, 423, & 421 

15

Scuff Cover Replacement Instructions 
(LRX Models) 

1.  Remove the foot cushion from the chair by 

loosening the two screws on the underside of 

the foot using a Phillips screwdriver. (See also 

“Unpacking and Set-up” on page 8.)

2.  Remove the scuff cover from the foot section 

(attached with Velcro®).

3.  Place the replacement scuff cover on a flat 

surface.

4.  Place the foot cushion on top of the scuff cover, 

centered left to right. (See “Figure 1” on page 

15.)

5.  Align the edge of the Velcro® on the bottom 

edge of the scuff cover with the foot cushion. 

Stretch the scuff cover over the bottom edge.

6.  Slide the foot cushion on the scuff cover to 

tighten.

7.  Stretch the sides and attach the Velcro® in 2 

places on each side.

8.  Reattach the foot cushion to the chair. (See 

also “Unpacking and Set-up” on page 8 for 

installation instructions.)

Figure 1

Calls for Service

Equipment’s model and serial number information are 

required when calling for service.

Serial number is indicated by the 

 symbol 

located on the serial number tag.

If service is required, contact MTI

U.S. & Canada 888-520-4998 

International 801-875-4998 

Fax (801) 952-0548 

[email protected] 

Monday-Friday 8:00 am - 5:00 pm (MST) 

www.mti.net

LIMITED WARRANTY

Medical Technology Industries, Inc. (hereinafter referred to 
as MTI), shall repair or replace products of its manufacture, 
which prove to be defective in material and/or workmanship 
for a period of twelve (12) months from the date of 
shipment to the customer (the “Warranty Period”). MTI will, 
at its option, provide parts to the customer or repair the 
defective part at MTI’s factory or authorized repair facility. 
Except as it may otherwise specifically agree in writing, MTI 
shall not be liable for transportation or labor charges for 
repairs or adjustments or other work done on any of its 
products by MTI’s authorized dealers or service organizations.

Customer shall notify MTI of any alleged claim or defect 
within fourteen (14) days from the date customer discovers, 
or upon reasonable inspection should have discovered, 
such alleged claim or defect (but in any event before the 
expiration of the Warranty Period). All repair parts are 
warranted for Ninety (90) calendar days from the date of 
shipment to the customer. Warranty is non-cumulative.

This warranty does not apply to any part or product 
which upon examination by MTI or its authorized agents 
indicates the product has been repaired or altered in any 
way by persons other than MTI or its authorized agents, 
has been misused, abused or used in a manner contrary 
to any instructions issued by MTI. Any parts or products 
claimed under this warranty must be properly packaged by 
customer and returned to MTI’s factory with no liability to 
MTI for the parts, products or transportation charges thereon.

In no event, shall MTI have any liability for consequential, 
indirect, incidental, special, exemplary, punitive or enhanced 
damages, lost profits or diminution in value arising 
out of or relating to a product defect or the repair or 
replacement of any products manufactured or sold by it.

THE FOREGOING LIMITED WARRANTY IS MADE IN LIEU 
OF ALL WARRANTIES EXPRESSED OR IMPLIED, AND MTI 
MAKES NO OTHER WARRANTY WHATSOEVER WITH 
RESPECT TO THE PRODUCTS INCLUDING BUT NOT LIMITED 
TO, ANY IMPLIED WARRANTY OR MERCHANTABILITY 
OR FITNESS FOR A PARTICULAR PURPOSE.

Summary of Contents for 421

























Reviews: