background image

34

MTH F3 Diesel Engine

O-31 OPERATION

  While the MTH F-3 diesel is more than capable of operating on O-31
curves and switches, you may find that certain light freight cars are prone to 
derailing when being pulled or pushed by the MTH F-3 through O-31
switches.  Should this occur, we suggest adding weight to the cars making
them heavier and less likely to derail.

WARNING:

  When using electrical products, basic safety precautions should be
followed including the following:

--  Read this and all related manuals (transformer/power supply,
locomotive, etc.) thoroughly before using this device.

--  This device is not recommended for children under eight years of age
without adult supervision.

--  MTH recommends parents examine the toy transformer used to power
this device periodically for conditions that may result in the risk of fire,
electric shock, or injury to persons, such as damage to the primary or output 
cord, plug blades, housing or other parts (including proper functioning of
the circuit breaker), and that, in an event such conditions exist, the
transformer should not be used until properly repaired.

Summary of Contents for MTH F-3 DIESEL ENGINE









































Reviews: