background image

11

MTH 392E Operating Manual

TINPLA

TE

Option 2:

If you do not have a separate bell button on your layout (or transformer), you can

still activate the Feature with your transformer whistle button. To activate the Feature utilizing

this method, turn on the transformer throttle and get your engine into the Neutral position (not

RESET). Once in Neutral, set the transformer throttle at 8 volts or less and press and hold the

whistle button for at least three seconds. You will hear the bell chiming turn on and if you

listen carefully, you should hear an

air-release sound effect after three

seconds have passed at which time

you can release the whistle button.

(

Note

:

because the air release

sound may be difficult to hear, we

recommend that you count out a

full three seconds before releasing

the whistle button

). The bell will

continue to chime so if you want to

turn off the bell chiming, simply press and release the whistle button a second time. Next,

interrupt the throttle to enter either Forward or Reverse to allow the engine to begin running.

(

Note

:

the Feature will only be activated for the first direction state you enter after leaving the

Neutral position. You cannot interrupt the throttle to enter another direction state and still

have the Feature remain active.

) Once your engine begins running, you can trigger the sounds

to begin playing whenever you enter Neutral.

ACTIVATING FREIGHT YARD SOUNDS

Once the Feature is activated, FYS will be played the next time the engine enters the Neutral

position. In order for FYS to begin, power must remain on once the engine enters the Neutral

position. At this point, ProtoSounds® has taken over control of your engine and disabled the

bell and whistle buttons from any further operator actions. In addition, ProtoSounds® has

reconfigured the way the reverse unit functions by disabling the reverse state during operation

of the FYS feature. This forces the engine to leave your freight yard in the same direction it

arrived in. The following operator controlled “events” control FYS’s actions and sounds.

Event 1 (Forward)

While the locomotive is running in forward (or reverse) FYS is

activated by the operator pushing and holding the bell button down for three or more seconds.

The locomotive bell begins chiming and can be left on or turned off without disabling FYS.

Event 2 (Neural Before Reverse)

The operator now interrupts the transformer throttle

to stop the engine and put it into Neutral. If the throttle setting was at 14 volts or higher ,

ProtoSounds® will play the sound of squeaking brake sounds as the engine comes to a halt.

A. Upon stopping of the engine, the operator must

immediately turn the throttle back on to keep the

engine in the Neutral position. If the bell was not

turned off after activating FYS, it now turns off

automatically.

Ding,

Ding

Psshhee

Put Engine In Neutral
At Low Power

Press & Hold

The Whistle Button

For 3 Seconds

Listen For The

Start Of The Bell Sound

Listen For The

Air Release Sound

After 3 Seconds

H

Put Engine In Neutral

At Low Power

Summary of Contents for 10-1091-1
































Reviews: