MTE Matrix APAX Installation Manual Download Page 6

Matrix

®

 APAX Installation Guide 380V - 415V

 

Form: MX-IG-E January 2018 REV. 002                    mtecorp.com                                            6 

2. INTRODUCTION 

 
The purpose of this manual is to aid in the proper installation of the Matrix® APAX. 
 
For most current product information, including technical reference manual, please refer to 
website: 

http://www.mtecorp.com/products/matrix-apax-harmonic-filters/ 

 
This manual is intended for use by personnel experienced in the operation and maintenance of 
drives. Because of the high voltages required by the filter, drive and the potential dangers 
presented by rotating machinery, it is essential that all personnel involved in the operation and 
maintenance of this filter know and practice the necessary safety precautions for this type of 
equipment. Personnel should read and understand the instructions contained in this manual 
before installing, operating or servicing the filter and drive to which it is connected. 

 

Receipt & Repair Statement

 

 

Upon Receipt of this Filter:

 

 
The Matrix APAX Harmonic Filter has been subjected to demanding factory tests before 
shipment. Carefully inspect the shipping container for damage that may have occurred in transit. 
Then unpack the filter and carefully inspect for any signs of damage. Save the shipping 
container for future transport of the filter. 
 

In the event of damage, please contact and file a claim with the freight carrier involved 
immediately. 

 
If the equipment is not going to be put into service upon receipt, cover and store the filter in a 
clean, dry location. After storage, ensure that the equipment is dry and that no condensation or 
dirt has accumulated on the internal components of the filter before applying power. 
 

Repair/Exchange Procedure

 

 
MTE Corporation requires a Return Material Authorization Number and form before we can 
accept any filters that qualify for return or repair. If problems or questions arise during 
installation, setup, or operation of the filter, please contact MTE for assistance at: 
 
Toll Free: 1-800-455-4MTE (1-800-455-4683) 
 
International Tel: +1-262-253-8200 
 
Fax: +1-262-253-8222 
 

Warranty 

 

One year from the date of shipment. See 

www.mtecorp.com

 for details. 

 

 

Summary of Contents for Matrix APAX

















Reviews: