background image

SECTION 3: ASSEMBLING YOUR TRIMMER

7

FIGURE 1

FIGURE 2

FIGURE 3

Decal

On some units, the J-handle may be pre-installed, requiring
only screw loosening and J-handle adjustment tailored to the
operator. Go to step 6 to adjust the J-handle if it is pre-installed.

INSTALLING AND ADJUSTING THE J-HANDLE

Installing

1.

Remove the screws, nuts, and top and middle clamp
pieces that were installed on the J-handle for
shipping.

2.

Place the J-handle between the top and middle
clamp pieces, Figure 1.

(4) Screws

Top Clamp

J-Handle 

Middle Clamp

Bottom Clamp

Nuts

3.

While holding the three pieces together, install the four (4)
screws through the top clamp and into middle clamp.

NOTE:

The holes in the top and middle clamp will line
up only when assembled correctly.

4.

Place the clamps and the J-handle over the shaft
housing and onto the bottom clamp.

5.

Hold each hex nut in the bottom clamp recess with a
finger. Start screws with a large Phillips screwdriver.
Do not tighten until you make the handle adjustment.

Adjusting

6.

Loosen the screws so that the J-handle can be
easily moved in the clamp assembly. Do not remove
the screws or nuts.

7.

Slide the J-handle in or out until the arrow/white line on
the decal touches the clamp assembly, Figure 2.

8.

While holding the unit in the operating position,
position the J-handle to the location that provides
you the best grip, Figure 3.

9.

Tighten the clamp screws evenly, until the J-handle
is secure.

Summary of Contents for Yard Machines LT31CS

























Reviews: