background image

31

CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The California Air Resources Board and MTD LLC are pleased to explain the evaporative emission control system warranty on your 2006 lawn mower. In California, 
new lawn mower must be designed, built and equipped to meet the State’s stringent anti-smog standards. MTD LLC must warrant the EECS on your lawn mower 
for the period of time listed below provided there has been no abuse, neglect or improper maintenance of your lawn mower.

Your EECS may include parts such as the carburetor, fuel-injection system, the ignition system, catalytic converter, fuel tanks, fuel lines, fuel caps, valves, 
canisters, filters, vapor hoses, clamps, connectors, and other associated emission-related components.

Where a warrantable condition exists, MTD LLC will repair your lawn mower at no cost to you including diagnosis, parts and labor.

MANUFACTURER’S WARRANTY COVERAGE:

This evaporative emission control system is warranted for two years. If any evaporative emission-related part on your equipment is defective, the part will be 
repaired or replaced by MTD LLC.

OWNER’S WARRANTY RESPONSIBILITIES:

As the lawn mower owner, you are responsible for performance of the required maintenance listed in your owner’s manual.  MTD LLC recommends that you retain 
all receipts covering maintenance on your lawn mower, but MTD LLC cannot deny warranty solely for the lack of receipts.

As the lawn mower owner, you should however be aware that MTD LLC may deny you warranty coverage if your lawn mower or a part has failed due to abuse, 
neglect, or improper maintenance or unapproved modifications.

You are responsible for presenting your lawn mower to MTD LLC’s distribution center or service center as soon as the problem exists. The warranty repairs should 
be completed in a reasonable amount of time, not to exceed 30 days. If you have a question regarding your warranty coverage, you should contact the MTD 
Service Department at 1-800-800-7310.

GENERAL EMISSIONS WARRANTY COVERAGE:

MTD LLC warrants to the ultimate purchaser and each subsequent purchaser that the lawn mower is: Designed, built and equipped so as to conform with all 
applicable regulations; and free from defects in materials and workmanship that cause the failure of a warranted part to be identical in all material respects to that 
part as described in MTD LLC’s application for certification.

The warranty period begins on the date the lawn mower is delivered to an ultimate purchaser or first placed into service. The warranty period is two years.

Subject to certain conditions and exclusions as stated below, the warranty on emission-related parts is as follows:

1.  Any warranted part that is not scheduled for replacement as required maintenance in the written instructions supplied, is warranted for the warranty period 

stated above. If the part fails during the period of warranty coverage, the part will be repaired or replaced by MTD LLC according to subsection (4) below. Any 
such part repaired or replaced under warranty will be warranted for the remainder of the period.

2.  Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period stated above. Any such 

part repaired or replaced under warranty will be warranted for the remaining warranty period.

3.  Any warranted part that is scheduled for replacement as required maintenance in the written instructions supplied is warranted for the period of time before 

the first scheduled replacement date for that part. If the part fails before the first scheduled replacement, the part will be repaired or replaced by MTD LLC ac-
cording to subsection (4) below. Any such part repaired or replaced under warranty will be warranted for the remainder of the period prior to the first scheduled 
replacement point for the part.

4.  Repair or replacement of any warranted part under the warranty provisions herein must be performed at a warranty station at no charge to the owner. 

5.  Notwithstanding the provisions herein, warranty services or repairs will be provided at all of our distribution centers that are franchised to service the subject 

engines or equipment.

6.  The lawn mower owner will not be charged for diagnostic labor that is directly associated with diagnosis of a defective, emission-related warranted part, 

provided that such diagnostic work is performed at a warranty station.

7.  MTD LLC is liable for damages to other engine or equipment components proximately caused by a failure under warranty of any warranted part.

8.  Throughout the lawn mower warranty period stated above, MTD LLC will maintain a supply of warranted parts sufficient to meet the expected demand for such 

parts.

9.  Any replacement part may be used in the performance of any warranty maintenance or repairs and must be provided without charge to the owner. Such use will 

not reduce the warranty obligations of MTD LLC.

10. Add-on or modified parts that are not exempted by the Air Resources Board may not be used. The use of any non-exempted add-on or modified parts by the 

ultimate purchaser will be grounds for disallowing a warranty claims. MTD LLC will not be liable to warrant failures of warranted parts caused by the use of a 
non-exempted add-on or modified part.

WARRANTED PARTS:

The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty coverage if MTD LLC demonstrates 
that the lawn mower has been abused, neglected, or improperly maintained, and that such abuse, neglect, or improper maintenance was the direct cause of the 
need for repair or replacement of the part. That notwithstanding, any adjustment of a component that has a factory installed, and properly operating, adjustment 
limiting device is still eligible for warranty coverage. The following emission warranty parts list are covered: Fuel Line, Fuel Line Clamps

Summary of Contents for 791

































Reviews: