background image

8

4

Operating 

Your Snow 

Thrower

Now that you have set up your snow thrower for 
operation, get acquainted with its controls and fea-
tures. These are described below and illustrated  in 

Figure 1

. This knowledge will allow you to use your 

new equipment to its fullest potential. 

NOTE:  For detailed starting instructions and more 
information on all engine controls, refer to the separate 
engine manual packed with your unit

Shift Lever

The shift lever is located in the right side of the handle 
panel and is used to determine gorund speed and 
direction of travel.

Forward

There are six forward (F) speeds. Position one (1) is the 
slowest and position six (6) is the fastest. 

Reverse

There are two reverse (R) speeds. One (1) is the slower 
and two (2) is the faster.

Know Your Snow Thrower

Choke Control

The choke control is found on the rear of the engine and 
is activated by rotating the knob clockwise. Activating the 
choke control closes the choke plate on the carburetor 
and aids in starting the engine.

Throttle Control

The throttle control is located on the 
engine. It regulates the speed of the 
engine and will shut off the engine when 
pushed down completely.

Primer

Depressing the primer forces fuel directly 
into the engine’s carburetor to aid in 
cold-weather starting.

Oil Fill

Engine oil level can be checked and oil 
added through the oil fill.

WARNING

Read, understand, 
and follow all instruc-
tions and warnings 
on the machine and 
in this manual before 
operating.

Use extreme care 
when handling 
gasoline. Gasoline is 
extremely flammable 
and the vapors are 
explosive. 

Never

 fuel 

the machine indoors 
or while the engine 
is hot or running. 
Extinguish cigarettes, 
cigars, pipes and 
other sources of 
ignition.

Figure 1

%NGINE#ONTROLS

2ECOIL3TARTER

(ANDLE

%LECTRIC3TARTER/UTLET

0RIMER

)GNITION

+EY

#HOKE

#ONTROL

4HROTTLE

#ONTROL

$RIVE#ONTROL

/IL&ILL

#HUTE!SSEMBLY

'AS#AP

3HIFT,EVER

!UGER#ONTROL

#HUTE$IRECTIONAL#ONTROL

%LECTRIC3TART"UTTON

#LEAN/UT

4OOL

!UGERS

3KID3HOE

34/0

NOTE: Snow throwers vary 
by model with regard to 
features and components. 
Your snow thrower may 
NOT resemble, in detail, 
snow throwers illustrated 
in figures  throughout this 
manual.

Summary of Contents for 769-01275D





























Reviews: