background image

Finding and Recording Model Number

Please do 

NOT return the unit to the retailer from which it was purchased,  

without first contacting Customer Support.

Table of Contents

BEFORE YOU START ASSEMBLING  
YOUR NEW EQUIPMENT, 
please locate the model plate on the equipment and copy the 
information to the sample model plate provided to the right. 
You can locate the model plate by standing at the operating 
position and looking down at the rear of the deck . This 
information will be necessary to use the manufacturer’s web 
site and/or obtain assistance from the Customer Support 
Department or an authorized service dealer.

This Operator’s Manual is an important part of your new snow thrower. It will help you assemble,  

prepare and maintain the unit for best performance. Please read and understand what it says. 

Customer Support

If you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance of this unit, 
you can seek help from the experts. Choose from the options below:

Safety Labels ...................................................... 3
Safe Operation Practices ................................... 4
Setting Up Your Snow Thrower .......................... 6
Operating Your Snow Thrower ........................... 8 
MakingAdjustments ......................................... 1

Maintaining Your Snow Thrower ...................... 14
Off-SeasonStorage ........................................... 18
Trouble- Shooting ............................................. 19
Illustrated Parts List ......................................... 0
Warranty .............................................Back Cover

1.  Visit 

mtdproducts.com

 for many useful suggestions. Click on 

Customer Support button and you will get the options reproduced in 
the screen shot below. Click on the appropriate button and help is 
immediately available.

2.  Phone a 

Customer Support Representative at 1(800) 800-7310.

3.  The 

engine manufacturer is responsible for all engine-related issues 

with regard to performance, power-rating, specifications, warranty and 
service. Please refer to the engine manufacturer’s Owner’s/Operator’s 
Manual, packed separately with your unit, for more information. 

 

www.mtdproducts.com

MTD  LLC

P. O. BOX  361131

CLEVELAND,OH 44136

330-220-4683

800-800-7310

Summary of Contents for 769-01275D





























Reviews: