background image

11

SECTION 4:  KNOW YOUR SNOW THROWER

WARNING: 

Be familiar with all the 

controls and their proper operation. Know 
how to stop the machine and disengage 
them quickly.

Throttle Control

The throttle control is located on the engine. It regulates 
the speed of the engine. See Figure 18.

Safety Ignition Switch

The ignition key must be inserted in the switch before 
the unit will start. Remove the ignition key when snow 
thrower is not in use.

Fuel Shut-Off Valve (If Equipped)

The fuel shut-off valve, 
located under fuel tank, 
control fuel flow from tank.  
See Figure 17. 

Figure 17

Figure 18

Shift Lever

(See Figure 19 for Models 602, 642, and 662.) See 
Figure 20 models 614, 644, 664, and 6A4) 

The shift lever is located in the center of the handle 
panel. The shift lever may be moved into one of six 
positions. Run engine with throttle in the fast positions 
Run engine with throttle in the fast position. Use the 
shift lever to determine ground speed.

Forward-Five forward speeds: position one (1) is the 
slowest; position five (5) is the fastest.

Reverse-One reverse (R) speed.

NOTE: 

Model 614, 644, 664, and 6A4 has five

forward positions and two reverse.

Auger Control Clutch

(See for Model 602, 642, and 662. See Figure 20 for 
Models 614, 644, 664, and 6A4)

The auger control clutch is located on the left handle. 
Squeeze the auger control clutch against the handle to 
engage the augers. Release to stop the snow throwing 
action.

Traction Control Clutch

(See Figure 19 for Model 602, 642, and 662. See 
Figure 20 for Models 614, 644, 664, and 6A4)

The traction control clutch is located on the right 
handle. Squeeze the traction control clutch to engage 
the wheel drive. Release to stop.

Chute Directional Control

(See Figure 19 for Model 602, 642, and 662. See 
Figure 20 for Models 614, 644, 664, and 6A4)

The chute directional control is located on the left hand 
side of the snow thrower. To change the direction in 
which the snow is thrown, turn chute directional control 
as follows: 

Crank clockwise to discharge to the left.

Crank counterclockwise to discharge to the right.

Stopping Engine

Remove ignition key from the snow thrower.          
Do not turn key.

 

Figure 19

Closed

Open

Ignition

Key

Choke

Throttle

Primer

Starter

Handle

Chute

Directional Control

Auger

Control

Clutch

Traction 

Control

Clutch

Shift

Lever

Models 602, 642 and 662

Summary of Contents for 602E





























Reviews: