background image

14

S

ection

 6— M

aintenance

 & a

djuStMentS

4. 

Lift the chute deflector up to keep it out of the way. See  

Figure 6-2

B.

5. 

Remove the two hairpin clips from each clevis pin which 

extend through the housing and remove pins. See  Figure 

6-2C.

6. 

Remove the flail screen from inside the housing and clean 

the screen by scraping or washing with water. See  Figure 

6-1D.

7. 

Reinstall the screen, making certain to reassemble the flail 

screen with the curve side down.

8. 

Reattach the chute deflector with the hardware previously 

removed and connect the bag to unit.

Removing the Flail Screen

WARNING: 

The impeller’s shredder blade and 

chipper blades are sharp. Wear leather work gloves 

to protect your hands when cleaning out the 

reduction chamber.

If the discharge area becomes clogged, remove the flail screen 

and clean area as follows:
1. 

Stop engine and make certain the chipper shredder has 

come to a complete stop.

WARNING: 

The muffler and surrounding area will 

be hot if the engine has been running. Use caution 

and protect your hands if working near the muffler. 

2. 

Disconnect spark plug wire from spark plug and ground 

against the engine.

3. 

Remove the bag and two wing knobs on each side of the 

chute deflector. See  Figure 6-2A.

Figure 6-2

Summary of Contents for 45M4 Series





















Reviews: