26
MAINTENANCE AND OPERATING MANUAL
Chapter 7 - Electronic Board
The data inside this manual are not binding and they can be modified by the manufacturer without notice.
All rights reserved.
TAEevo015÷351
NOTE
The new value is stored also when the programming procedure is terminated for “time out”, without pressing
-
button.
ATTENTION
You can modify the parameter of the
CF
(configuration parameters) family only when the unit is in stand by.
7 . 9
V a l u e s d i s p l a y e d
The values visualized on the display change according to the configuration of parameters
CF36
for the top part and
CF42
for the bottom part.
For remote terminal it changes according to the configuration of parameters
CF43
for the top part and
CF44
for the bottom part.
Parameter CF36/CF43 = 0
In the top part of the display it appears the probe
BEWOT
Parameter CF36/CF43 = 1
In the top part of the display it appears the probe
BTWOT
Parameter CF36/CF43 = 2
No value will appear in the top part of the display
Parameter CF36/CF43 = 3
In the top part of the display it appears the probe
BAT1
Parameter CF36/CF43 = 4
In the top part of the display it appears the chiller set; off when unit in stand-by
Parameter CF36/CF43 = 5
In the top part of the display it appears “OnC” when the unit is operating; off when unit in stand-by
Parameter CF36/CF43 = 6
In the top part of the display it appears the LASER set (FUNCTION NOT ENABLED)
Parameter CF36/CF43 = 7
No value will appear in the top part of the display
Parameter CF36/CF43 = 8
In the top part of the display it appears the operating differential
Parameter CF42/CF44 = 0
In the bottom part of the display it appears the probe
BEWOT
Parameter CF42/CF44 = 1
In the bottom part of the display it appears the probe
BTWOT
Parameter CF42/CF44 = 2
In the bottom part of the display it appears the probe
PCP1
Parameter CF42/CF44 = 3
In the bottom part of the display it appears the probe
BAT1
Parameter CF42/CF44 = 4
In the bottom part of the display it appears the chiller set; off when unit in stand-by
Parameter CF42/CF44 = 5
In the bottom part of the display it appears “OnC” when the unit is operating
Parameter CF42/CF44 = 6
In the bottom part of the display it appears the LASER set (FUNCTION NOT ENABLED)
Parameter CF42/CF44 = 7
No value will appear in the bottom part of the display
Parameter CF42/CF44 = 8
In the bottom part of the display it appears the operating differential
If the probe
BTWOT
has been selected has default, every time you press
(
for 30 sec the top display visualizes the
BEWOT
probe, in the
bottom part of the display it will appear the “Label”
Pb2
than the default value will return to be displayed.
If the probe
BEWOT
has been selected has default, every time you press
(
for 30 sec the top display visualizes the
BTWOT
probe, in the
bottom part of the display it will appear the “Label”
Pb1
than the default value will return to be displayed.
7 . 1 0 U n i t s w i t c h i n g o n / o f f
The pressure of
'
button for 5 seconds allows to switch on or off the unit.
The led of icon
flashes for 5 seconds then it remains lit.
7 . 1 1 H o w t o p u t t h e u n i t i n s t a n d - b y
Stand-by modality is obtained every time the unit is switched off.
It is indicated by the symbol
P
lit.
Also in stand-by modality the controller can:
1.
Display the measured values
2.
Manage the alarms by displaying and signalling.
Summary of Contents for TAEevo015
Page 3: ......
