background image

FILTER PUMP 

DOES NOT

WORK

SPA TUB IN AN 

ABNORMAL 

SHAPE

Extra air pressure by strong sunlight

Check the air pressure and release some air if necessary.

During hot weather, it is recommended to 

check if it is necessary to release some air to avoid any possible 

damage to the spa pool

SPA LEAKING

Spa inlet/outlet connection not securely tight

Drainage valve is not closed completely

Water leaks from the spa pool body

Repair the leaking hole/spilt with the repair kit material

Tighten the inlet and outlet connection

Close the drainage valve. Contact the MSpa Service Center, if spa 

is still leaking

Filter stuck by dirt or other objects

Filter system failure

Clean or replace the filter cartridge

Contact local MSpa Service Center

NO BUBBLE

Auto-off 10 minutes

Unidirectional threshold is not open

Control panel failure

Inflation knob is in <ON> position

Wait for 10 minutes

Contact local MSpa Service Center 

Contact local MSpa Service Center 

Turn the knob to <OFF> position and turn on the bubble button again.

LED READING

CAUSE

SOLUTION

E0

E1

Water temperature is lower than 0°C degree or exceeds 55°C (131°F)
Temperature sensor failure
Waterflow switch failure
Filter failure
Water level is not at minimum water line

Contact local MSpa Service Center.

Add water above the minimum line.

Change the water or contact local MSpa Service Center.

ERROR CODE CHART

TROUBLESHOOTING

PROBLEM

CAUSE

SOLUTION

NO DISPLAY ON

THE WIRED

CONTROLLER  

Power failure

PRCD is off

PRCD broken

Contact local MSpa Service Center

Contact local MSpa Service Center

NOT HEATING 

PROPERLY

Temperature set too low

Dirty filter cartridge

Heater failure

Filter pump broken

Temperature protection switch trip off

Set a higher temperature

Clean or replace the filter cartridge 

Add more water to the minimum line 

Contact local MSpa Service Center

Contact local MSpa Service Center

Reset the heater

Press the Reset button, Control Panel is not displayed 

Water level is not at the minimum water line 

Reset PRCD by following PRCD Testing section

Check power supply

17

Summary of Contents for P-CA049



















Reviews: