background image

 

FCC STATEMEMT: 

This device is intended only for OEM integrators under the following conditions: 

1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 

2) The transmitter module may not be co-located with any other transmitter or antenna. 

As long as 2 conditions above are met, further transmitter test will not be required. However, the 

OEM integrator is still responsible for testing their end-product for any additional compliance 

requirements required with this module installed (for example, digital device emissions, PC peripheral 

requirements, etc.). 

IMPORTANT NOTE:   

In the event that these conditions can not be met (for example certain laptop configurations or 

co-location with another transmitter), then the FCC authorization is no longer considered valid and 

the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be 

responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC 

authorization. End Product Labeling This transmitter module is authorized only for use in device 

where the antenna may be installed such that 20 cm may be maintained between the antenna and users 

(for example access points, routers, wireless ADSL modems, and similar equipment). The final end 

product must be labeled in a visible area with the following: "Contains TX FCC ID

I4L-MS6833A".  

Manual Information for End Users   

The end user must not have manual instructions to remove or install the device. The user manual for 

end users must include the following information in a prominent location: "IMPORTANT NOTE: To 

comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must 

be installed to provide a separation distance of at least 20 cm from all persons and must not be 

co-located or operating in conjunction with any other antenna or transmitter."

 

Summary of Contents for MP54G4 (MS-6833A)
















Reviews: