manualshive.com logo in svg

MSI 790XT-G35 series, Manual

Share
Download
MSI 790XT-G35 series Manual Download Page 58

3-24

BIOS Setup

▍

MS-7388

BIOS Setup

▍

MS-7388

Remember to dsable Spread Spectrum f you are overclockng because even a slght 

jtter  can  ntroduce  a  temporary  boost  n  clock  speed  whch  may  just  cause  your 

overclocked processor to lock up. 

•

Important

Faled Overclockng Resoluton  

Ths  motherboard  supports  overclockng  greatly.  However,  please  make  sure  your 

perpherals and components are bearable for some specal settngs. Any operaton that 

exceeds product specficaton s not recommended. Any rsk or damge resultng from 

mproper operaton wll not be under our product warranty.
Two ways to save your system from faled overclockng...

Reboot
Press the Power button to reboot the system three tmes. Please note that, to avod 

electrc current to affect other devces or components, we suggest an nterval of more 

than 10 seconds among the reboot actons.

At the fourth reboot, BIOS wll determne that the prevous overclockng s faled and 

restore the default settngs automatcally. Please press any key to boot the system 

normally when the followng message appears on screen.

Warnng !!! The prevous overclockng had faled, 

and system wll restore ts defaults settng, 

Press any key to contnue.......

Clear CMOS
Please refer to “Chapter 2” for more nformaton about how to clear CMOS data.

•

•

Summary of Contents for 790XT-G35 series








































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands