background image

Regulation (EU) n° 517/2014 of 16/04/14 on fluorinated greenhouse gases and 
repealing Regulation (EC) n°842/2006   

 

 

Leakage checks

 

1. Operators of the equipment that contains fluorinated greenhouses gases in quantities of 5 tons of 

CO2, equivalent or more and not contained in foams, shall ensure that the equipment are well 

checked for leakage. 

2.  For equipment that contains fluorinated greenhouse gases in quantities of 5 tons of CO2 

equivalent or more, but of less than 50 tons of CO2 equivalent: check leakage at least every 12 

months. 

 

Picture of the equivalence CO

2

 

1. Load in kg and Tons amounting CO2. 

 

Load and Tons amounting CO

2

 

Frequency of test

 

From 2 at 30 kg load = from 5 at 50 
Tons 

Each year 

 

Concerning the Gas R32, 7.41kg amounting at 5 tons of CO2, commitment to check each year.

 

Do  not  release  R32  coolant  liquid  into  the  atmosphere.  This  is  a  fluoride  greenhouse  effect  gas 

covered  by  the  Kyoto  agreement  with  a  global  warming  potential  (GWP)  =  675  -(see  the 

European  Community  regulations  on  fluoride  greenhouse  effect  gases  Regulation  (EU)  No 

517/2014).

 

 

Training and certification

 

1.  The  operator  of  the  relevant  application  shall  ensure  that  the  relevant  personnel  have  obtained  the 

necessary certification, which implies appropriate knowledge of the applicable regulations and standards 

as well as the necessary competence in emission prevention and recovery of fluorinated greenhouse gases 

and handling safety the relevant type and size of equipment. 

 

Record keeping

 

1. Operators of equipment which are required to check for leakage, shall establish 

and maintain records for each piece of such equipment specifying the following 

information: 

a) The quantity and type of fluorinated greenhouse gases installed; 

b) The quantities of fluorinated greenhouse gases added during installation, maintenance or service or due 
to leakage; 
c) Whether the quantities of installed fluorinated greenhouse gases have been recycled or reclaimed, 

including the name and address of the recycling or reclamation facility and, where applicable, the 

certificate number; 

d) The quantity of fluorinated greenhouse gases recovered; 
e) The identity of the undertaking which installed, serviced, maintained and where applicable repaired or 

decommissioned the equipment, including, where applicable, the number of its certificate; 

Summary of Contents for FO045HS


















Reviews: