MSA ZGARD C Instruction Manual Download Page 14

 

 

Section 4 

ZGARD C 4-Channel Controller 
Installation and Setup 

 

 
 

 
 
 
 
 
 
 
 
 

 
Setting-up Relay Functions: 

When jumper H1-3 is not inserted (OUT), all relays are normally de-energized when inactive and 
energized when activated. If jumper H1-3 is inserted (IN), then all relays are normally energized when 
inactive and de-energized when activated. 

 

 
 
Setting-up the Warning & Alarm Delays: 

There are two methods for setting the warning and alarm delays. The first uses pre-programmed, 
fixed delays of 5 minutes OFF delay for warning and 5 minutes ON delay for alarm. To select the fixed 
delay, jumper H1-5 must be inserted.  
 
The second allows adjusting of the delays from 0 to 10 minutes via two potentiometers (labeled: 
Warning Delay, Alarm Delay). To select the adjustable delay, jumper H1-5 is NOT inserted. Removing 
the jumper activates the associated potentiometer and test points (TP3 for warning delay and TP4 for 
alarm delay). The test points show a voltage of 0-5Vdc for a delay of 0 - 10 minutes. 

 
TP = Delay (minutes)/10 x 5Vdc 

 

Example:

 To set up a Warning delay of 4 minutes and an Alarm delay of 6 minutes, 

 

Warning Delay  

TP3 and TPCOM should read:

 Warning Delay (4/10) x 5 = 

2.0Vdc 

 

Alarm delay 

 

TP4 and TPCOM should read:

 Alarm Delay (6/10) x 5 = 

3.0Vdc 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

4.2

H1  

 

PARAMETER 

SETUP 

 

Number of Active Points 

 

 

1 + (0 -3 )

 

 

 

RELAY NORMALLY EN/DE (IN/ OUT) 

 

 

DISPLAY RANGE B/A (IN/ OUT) 

 

 

DELAY  5MIN. / POT (IN/ OUT) 

 

 

HORN  SOLID / VAR (IN / OUT) 

 

 

WARNING  POT / 35% (IN / OUT) 

 

 

ALARM  POT / 50% (IN / OUT) 

 

 

ALARM LATCH (IN) 

Summary of Contents for ZGARD C























Reviews: