ACCESSORIES
The facepiece may be equipped with the following acces-
sories:
1. Cover Lens (clear or tinted), in small, medium, or large
2. Spectacle Kit
Refer to the NIOSH Approval Matrix for a complete list
of Approved Accessories. If you must wear corrective
eyewear, install an approved spectacle kit, listed on
the NIOSH approval matrix insert.
Know the contaminant(s) in the environment before
entering. Always check that the filter canis-
ter/cartridge(s) is appropriate for use in the environ-
ment. A filter canister/cartridge(s) which is not
designed for the contaminant present may not provide
protection. Failure to follow this warning can result in
serious personal injury or death.
Installing the Nosecup for Advantage 3000 Facepiece
1. Place nosecup into facepiece with notch of nosecup
facing the bottom of facepiece.
2. Place bottom of nosecup under facepiece seal.
3. Stretch nosecup over Inhalation Valve Housing ensur-
ing notch of nosecup is over tab of inhalation valve
housing.
4. Stretch nosecup around lip on inhalation valve hous-
ing ensuring nosecup is in place.
Spectacle Kit
Spectacle kits are available for the Advantage 3000 (P/N
10029298). The kit includes the support assembly, a rub-
ber block, and the spectacle frame. Prescription lenses
can be obtained locally or through MSA.
Adjusting the Spectacles
1. To move the spectacles closer to your face, pull the
frame prongs out of the rubber block.
2. To move the spectacles farther from your face, push
the frame prongs into the rubber block.
3. To move the spectacles
up or down, slide the
rubber block up or
down on the support
arms.
Attaching the Gas Mask Chin Canister to the Belt
This conversion kit consists of:
Installation Instructions
1. Attach the male thread end of the breathing tube
securely to the facepiece component housing.
2. Slide the belt clip over the neck of the canister.
3. Securely fasten the female end of the breathing tube
to the male end of the canister.
4. Attach the belt around the waist and attaché the belt
clip to the belt.
Spark Cover (P/N 10068152)
1. Remove canister and spark cover from the packaging.
2. Attach the canister to the facepiece or breathing tube
depending on the configuration being used.
3. Once the canister is attached, align the feet of the
spark cover with the inlet hole of the canister.
4. Grasp the outside of
the canister, twist and
push on the spark
cover. The spark cover
will snap in place.
5. To remove the spark
cover, gently squeeze
the outside of the cover,
twist, and pull the spark
cover off.
27
TAL 013 (L) Rev. 10 - 10028994
Quantity
Item
Part Number
1
Belt Clip
10068195
1
Breathing Tube
10068129
1
Belt
473902, 9961, 492827
1
Spark Cover
10068152
motion for attaching
spark cover
check for optional spark
arresting material
Spark Arresting
Material
Summary of Contents for Advantage 3100
