Introduction
Please take a few moments to carefully read through this manual. Correct
maintenance and operation of this machine will provide the best possible
performance.
Safety Tips
• Position on a flat, stable surface.
• A service agent/qualified technician should carry out installation and any
repairs if required. Do not remove any components or service panels on this
product.
• DO NOT immerse in water, or use steam/jet washers to clean the unit.
• DO NOT cover the appliance when it is operating.
• DO NOT place the appliance near flammable materials and be sure fine
ventilation.
• DO NOT lay the cable over carpets or heat insulations. Do not cover the cable.
Keep away the cable from operating range and do not dunk it into water.
• Always carry, store and handle the appliance in a vertical position.
• Never tilt the appliance more than 45° from the vertical.
• ONLY use drinking or potable water when making ice cubes.
• Ensure the water pressure of the connected water supply is between 1kg/cm²
to 8kg/cm² (14.7-117psi).
• The device is to be used indoors only.
• Keep all packaging away from children. Dispose of packaging in accordance
to the regulations of local authorities.
• If the power cord is damaged, it must be replaced by a recommended qualified
technician in order to avoid a hazard.
• The separate three pole socket should be used and it must be grounded
-
.
• The rated capacity of wire should be over 10A
The wire could be
.
consisted by single ply or multiplies
.
1
Automatic Ice Maker
6
Device dose not work
(Without
any
lights
come on)
Power supply is interrupted
Power supply voltage is not
correct
Check the power supply
Cut off the power supply
Device
dose
not
work
(Only
switch
light
come on)
Power supply voltage is not
correct
PCB board damaged
Cut off the power supply
Replace it
Device
dose
not
work (The
light
ice full
come on)
Ice full occur
℃
Ambient temperature is below 6
Remove the ice cubes from basket
Keeping the ambient temperature is
more than 7
, restart it
℃
Device
dose
not
work (
and
ice full
fault
flash together)
Ice full sensor damaged or
does not connected
Replace or connect this sensor
Device dose not work
(
light flash)
fault
condenser sensor damaged or does
not connected
Replace or connect this sensor
Water low
ice full
and
flash together or the
fault
flash rapidly
Refrigerant leaked
Compressor does not run
℃
Ambient temperature is below 6
Check and recharge
Compressor damaged or the ambient
temperature is higher than 43
℃
Keeping the ambient temperature over
7
, restart it
℃
Fault water low ice
,
,
full
three lights flash
slowly
the HALL sensor is not in correct
position or damaged.
paddle motor damaged
adjust the position or replace it.
replace it
Only the
light
fault
flash
rapidly
(after
working a period.)
Turn ice motor damaged
Micro-switches do not function.
Water box broken
Water box was blocked by ice
cubes
Replace it
Replace or adjust position again
Replace it
Remove the ice cubes
Device stop after 2
minutes or more. (The
water low
light flashes)
Without water in water supply
source
Water inlet valve damaged or does
not connect
water level sensor not in correct
position
waiting for water supplying
Check valve connecting or replace it.
Water low
light
always come on
without water supply for more then
24 hours
stop the machine and restart it if water
supply is ready
Ice cubes stick in the
water box
The
electric
valve
does
not
function
Some ice remain in the water box
Check the valve electrical connecting
or replace it
Stop the machine and move it
No ice making no
fault indication
The electric valve was leak
Compressor does not run
Replace it.
Ask service
Ice cubes are not
very equal
Refrigerant leak
Recharge it
Problem Possible Cause Suggested Solution
Automatic Ice Maker
Summary of Contents for XBC
Page 2: ......
