background image

Outdoor Patio Heater

7

Operating Instructions and Owner’s Manual

 

WARNING: Keep any electrical supply cord away from any 

heated surfaces.

 

WARNING: Certain materials or items, when stored under 

the heater, will be subjected to radiant heat and could be 
seriously damaged.

HEATER VENTILATION

Unrestricted air flow during heater operation is essential to prevent the 
area above the installed heater from overheating. If your workshop/
utility building is tightly insulated (including windows, doors, openings, 
etc.) the following ventilating methods must be followed:

• 

An intake vent, or equivalent, from the exterior of the building 
and having an effective area of 75 square inches must be located 
below the heater (preferably within 2 feet of the building’s floor).

• 

Openings equivalent to intake vent would be: partially open doors 
and partially open windows.

• 

Openings of this size (5 inch by 13 inch, or 3 inch by 25 inch) will 
prevent dangerous heat build-up above the heater.

Ensure that no gas lines or electrical wiring or conduits will interfere 
with mounting of the heater to the wall.

Depending on local codes and requirements and the installer’s skill 
level, the sizing and installation of gas lines required to supply the 
heater may require the assistance of a professional. If in doubt as to 
these requirements, discuss the requirements of this manual with the 
dealer from whom the heater was purchased and your gas supplier, or 
call Mr. Heater customer service department at 1-800-251-0001.

4.72” (120mm)

4.72” (120mm)

13.39” (340mm)

4.33”

 (110mm)

Model MHRP37GL Installation Details

FIGURE 7

40

º

Model MHRP37GL Mounting Position

FIGURE 8

HEATER INSTALLATION

GENERAL INSTALLATION INFORMATION AND 
REQUIREMENTS

The required minimum clearances to combustible surfaces are 
illustrated in 

Table 3 and 4

• 

This heater may be mounted on any wall; however, it is 
recommended that the heater be mounted in the middle of the 
wall opposite any overhead doors.

• 

When selecting installation locations for this heater ensure that 
the opening of any exterior or interior doors or windows will not 
violate minimum clearances or contact any heater components.

• 

If an overhead door is installed in the building, verify that the 
heater is not installed in such a way as to interfere with door 
operation and verify that the door in its open position will not 
reduce clearances below the minimum requirements. Never 
mount the heater in such a way that would position the heater 
above an opened overhead door.

• 

In most cases the infiltration around your uninsulated entry doors 
and windows will provide enough air flow for efficient heater 

operation.

 

WARNING: ELECTRICAL GROUNDING INSTRUCTIONS: This 

heater is equipped with a three-prong (grounding) plug for 
your protection against shock hazard and should be plugged 

directly into a properly grounded three-prong receptacle. Do 

not cut or remove the grounding prong from this plug.

Summary of Contents for MHRP37GL





























































Reviews: