background image

 
There are 4 operating modes for this configuration. They are described below.  
 

3.1 On/Off Mode

  

To turn on the light, click the switch. The light will turn on at the previous level.  
To turn off the light, click the switch.  

3.2 Momentary Mode

  

To turn on the light in momentary mode, press the switch, the light will turn on at the previous level.  
To turn off the light in momentary mode, release the switch.  
 

3.3 Adjustment Mode

  

To adjust the brightness of the light, turn on the light, then press.  
The light will begin adjustment in the dimming direction unless it was already set to the dimmest level. If set at 
the dimmest level, adjustment will begin in the brightening direction.  
Release the switch and the light adjustment will cease and the new level will be stored in the EEPROM. 
Pressing the switch again will start the light adjustment in the opposite direction (the direction toggles each 
time).  
When the light reaches the dimmest or brightest level it will stay there until the switch is released.  
 

3.4 Autosleep Mode (default off)

  

If Autosleep is enabled (covered later in Menu Mode), the timer will reset and start counting whenever a switch 
click or press occurs. When 15 minutes goes by without a click or press, the Autosleep function will commence 
dimming the light. The brightness level will visibly drop after each subsequent minute until the lowest light 
level is reached. After a total of 60 minutes elapses from the last button action the light will turn itself off.  
 
A click or press during any time prior to 60 minutes elapsing will return the light to its original brightness level. 
Note: if a press is used, the light will not return to the original brightness level until the switch is released.  
 
If the light is set to the dimmest level, the Autosleep function will be temporarily disabled. This allows the light 
to be left in a low power locator mode or as a nightlight. Current consumption is <10mA in this mode. 
 

4 Configuration 1 (optional) 5 Discrete Levels

  

 
There are 6 operating modes for this configuration. They are described below. 
 

4.1 On/Off Mode

 

To turn on the light, click the switch. The light will turn on at the previous level or the Force level if Force is 
enabled. 
To turn off the light, click the switch. 
 

4.2 Adjustment Mode

 

To adjust the brightness of the light start with the light off, then press the switch. 
The light will always turn on at Level 1 (dimmest level) and in the brightening direction. 
Release the switch at the desired level, and that new level will be stored in the EEPROM. Pressing the switch 
again (within 1.5 seconds) will start the light adjustment in the opposite direction (the direction toggles each 
time). 
When the light reaches the dimmest or brightest level it will stay there until the switch is released. Once the 
switch is released for longer than 1.5 seconds no more brightness adjustment is possible without turning off the 
light and starting the sequence again. 
 
 

Summary of Contents for LionHeart

Page 1: ...S but A is preferred cell ONLY In a pinch a disposable CR123 battery w spacer wadded up aluminum foil will do can be used but any attempt to drive it with a power source other than these mentioned may result in long term if not immediate damage to your light When the long tube battery accessory becomes available then the Pila 168A or S but A is preferred is the specified battery to be used for sig...

Page 2: ...light level is reached After a total of 60 minutes elapses from the last button action the light will turn itself off A click or press during any time prior to 60 minutes elapsing will return the light to its original brightness level Note if a press is used the light will not return to the original brightness level until the switch is released If the light is set to the dimmest level the Autoslee...

Page 3: ...n a low power locator mode or as a nightlight Current consumption is 10mA in this mode 4 6 Force Mode This mode is selected from the power on menu covered later in this thread when we discuss the menu mode Force mode overrides the initial turn on brightness level that was set via the Adjustment Mode on the previous turn off The user can always set a new temporary light level by using the Adjustmen...

Page 4: ...een made and the light will then turn off 5 3 Three clicks Force Mode Enable Adjust Disable Note Force Mode is only applicable to Configuration Mode 1 Initially the LED will dim to indicate Force Level 1 dimmest will be active Each click will cycle to the next Force setting The sequence is Force Level 1 LED dim Force Level 2 LED med low Force Level 3 LED medium Force Level 4 LED med high Force Lev...

Reviews: