manualshive.com logo in svg

MQ Power WHISPERWATT DCA125SSIU, Operation And Parts Manual

Share
Download
MQ Power WHISPERWATT DCA125SSIU Operation And Parts Manual Download Page 28

PAGE 28 — DCA125SSIU 50 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #0 (12/22/08) 

OUTPUT TERMINAL PANEL CONNECTIONS

UVWO TERMINAL OUTPUT VOLTAGES

Various output voltages can be obtained using the UVWO 
output terminal lugs. The voltages at the terminals are 
dependent on the position of the 

Voltage Selector Switch

 

and the adjustment of the 

Voltage Regulator Control 

Knob

.

Remember the voltage selector switch determines the 

range

 of the output voltage. The voltage regulator (VR) 

allows the user to increase or decrease the selected 
voltage.

3Ø-220/127 UVWO Terminal Output Voltages

Place the voltage selector switch in the 3Ø 240/139 

1. 

position as shown in Figure 18..

Voltage Selector Switch

Figure 18. 

3Ø-240/139V Position

Connect the load wires to the UVWO terminals as 

2. 

shown in Figure 19.

 UVWO Terminal Lugs 

Figure 19. 

3Ø-220/127V Connections

Turn the voltage regulator knob (Figure 20) clockwise 

3. 

to increase voltage output, turn counterclockwise to 
decrease voltage output. Use voltage regulator 
adjustment knob whenever fi ne tuning of the output 
voltage is required.

Voltage Regulator Knob

Figure 20. 

3Ø-200V/1Ø-115V UVWO Terminal Output Voltages

Place the voltage selector switch in the 3Ø 240/139 

1. 

position as shown in Figure 21.

Voltage Selector Switch

Figure 21. 

3Ø-240/139V Position

Connect the load wires to the UVWO terminals as 

2. 

shown in Figure 22.

UVWO Terminal  Lugs

Figure 22. 

3Ø-200/1Ø-115V Connections Connections

NOTICE

To achieve a 3Ø 200V output the voltage selector switch 
must be in the 3Ø-240/139 position and the voltage 
regulator must be adjusted to 200V..

Summary of Contents for WHISPERWATT DCA125SSIU

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands