MQ Multiquip WHITEMAN B Series Operation And Parts Manual Download | Manualshive

Page: 8 / 124

background image

PAGE 8 — B-SERIES WALK-BEHIND TROWEL— OPERATION AND PARTS MANUAL — REV. #9 (07/06/10)

B-SERIES TROWEL— SAFETY MESSAGE ALERT SYMBOLS

Safety precautions should be followed at all times when operating
this equipment. Failure to read and understand the Safety
Messages and Operating Instructions could result in injury to
yourself and others.

FOR YOUR SAFETY AND THE SAFETY OF OTHERS!

This Owner's Manual has been developed to provide
complete instructions for the safe and efficient operation
of the MQ Whiteman B-SERIES TROWEL. For engine
maintenance information, please refer to the engine
manufacturers instructions for data relative to its safe
operation.

Before using this WALK-BEHIND TROWEL, ensure
that the operating individual has read and
understands all instructions in this manual.

NOTE

SAFETY MESSAGE ALERT SYMBOLS

The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words:

DANGER

,

WARNING

, or

CAUTION

.

DANGER:

You

WILL

be

KILLED

or

SERIOUSLY injured if you

DO NOT

follow

directions.

WARNING:

You

CAN

be

KILLED

or

SERIOUSLY injured if you

DO NOT

follow

directions.

CAUTION:

You

CAN

be injured if you

DO NOT

follow directions.

HAZARD SYMBOLS

Engine exhaust gases contain poisonous

carbon monoxide. This gas is colorless and

odorless, and can cause death if inhaled.

NEVER

operate this equipment in a confined

area or enclosed structure that does not

provide ample free flow air.

Potential hazards associated with B-Series trowel operation will
be referenced with "

Hazard Symbols

" which appear throughout

this manual, and will be referenced in conjunction with Safety
"

Message Alert Symbols

".

Gasoline is extremely flammable, and its
vapors can cause an explosion if ignited.

DO

NOT

start the engine near spilled fuel or

combustible fluids.

DO NOT

fill the fuel tank

while the engine is running or hot.

DO NOT

overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or
sparks from the ignition system. Store fuel in

approved containers, in well-ventilated areas
and away from sparks and flames.

NEVER

use fuel as a cleaning agent.

Burn Hazards

Engine components can generate extreme heat.
To prevent burns,

DO NOT

touch these areas

while the engine is running or immediately after
operations.

NEVER

operate the engine with

heat shields or heat guards removed.

Rotating Parts

NEVER

operate equipment with covers, or

guards removed. Keep fingers,

hands

,

hair

and

clothing

away from all moving parts to prevent

injury.

Explosive Fuel

Lethal Exhaust Gases

«
...
6
7
8
9
10
...
»

Summary of Contents for WHITEMAN B Series





























































































































Reviews:

No comments

Related manuals for WHITEMAN B Series

Brand: Allen Engineering Corporation Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands