background image

- 14 - 

Installation 

DIN rail, wall mount (with optional kit) 

Environmental Limits 

Operating 
Temperature 

Standard Models: -25 to 60°C (-13 to 140°F)   
Wide Temp. Models: -40 to 75°C (-40 to 167°F) 

Storage Temperature  -40 to 85°C (-40 to 185°F) 
Ambient Relative 
Humidity 

5% to 95% (non-condensing) 

Power Requirements 

Input Voltage 

12 to 48 VDC, redundant dual DC power inputs or 
48 VDC Power-over-Ethernet* (IEEE 802.3af 
compliant) 
*Discontinued starting with HW Rev 2.0.0 

Connector 

10-pin removable terminal block 

Power Consumption  12 to 48 VDC, 0.121 to 0.494 A 
Reverse Polarity 
Protection 

Present 

Standards and Certifications 

Safety 

UL 60950-1, EN 60950-1 

Hazardous Location  UL/cUL Class I Division 2, ATEX Zone 2 
EMC 

EN 301 489-1/17; FCC Part 15, Subpart B; EN 
55022/55024 

Radio 

EN 300 328, EN 301 893, TELEC, FCC ID 
SLE-WAPA003 

Note: Please check Moxa’s website for the most up-to-date 
certification status. 

Reliability 

MTBF   

392,209 hrs. 

Warranty 

Warranty Period 

5 years 

Details 

See www.moxa.com/support/warranty.aspx 

 

 

ATTENTION 

 

The AWK-3121 is 

NOT 

a portable mobile device and should 

be located at least 20 cm away from the human body. 

 

The AWK-3121 is 

NOT 

designed for the general public. A 

well-trained technician is required to deploy the AWK-3121 
units and safely establish a wireless network. 

 

 

 

ATTENTION 

This device complies with part 15 of the FCC Rules. Operation is 
subject to the following two conditions:   
1. This device may not cause harmful interference. 
2. This device must accept any interference received, including 
interference that may cause undesired operation. 

 

 

Summary of Contents for AirWorks AWK-3121
















Reviews: