manualshive.com logo in svg

movistar TSM 1, Reference Manual

Share
Download
movistar TSM 1 Reference Manual Download Page 67

Sequoia Reference Guide 

Chapter 8  Health and Safety Information 

 
 
 

For Body Operation 

To maintain compliance with FCC RF exposure requirements, use only belt-clips, 
holsters or similar accessories that maintain a 2.0 cm separation distance between the 
user’s body and the back of the phone, including the antenna, whether extended or 
retracted. The use of belt-clips, holsters and similar accessories should not contain 
metallic components in its assembly. The use of accessories that do not satisfy these 
requirements may not comply with FCC RF exposure requirements, and should be 
avoided. 

For more information concerning exposure to radio frequency signals, see the following 
websites: 

Federal Communications Commission (FCC) 

http://www.fcc.gov/oet/rfsafety

 

Cellular Telecommunications Industry Association (CTIA) 

http://www.wow-com.com 

U.S. Food and Drug Administration (FDA) 

http://www.fda.gov/cdrh/consumer

 

World Health Organization (WHO) 

http://www.who.int/peh-emf/en

 

 

8-2 

Summary of Contents for TSM 1




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands