Mountup MU2001 Instruction Manual Download Page 2

WARNING!

PACKAGE CONTENTS

01

B (x1)

VESA Plate

A (x1)

Arm Assembly

NOTE:

 Not all hardware included will be used.

D (x3)

Decorative Cover

E(x1)

6mm Allen Key

C (x1)

Bolt

(                            )

Installation Tools 

Level

Screwdriver

Pencil

Drill

Socket

Wrench

M-E (x4)

D6 Washer

M-C (x4)

M-B (x4)

M-D (x4)

M-A (x4)

M-F (x4)

M6 x 12mm

M4 x 16mm

M6 x 16mm

M4 x 12mm

Spacer H5mm

W-B (x3)

W-C (x3)

Washer

W-A (x3)

Lag Bolt M6 x 55mm

Anchor   Φ 9.6 x 43mm 

If you have any confusions or are not quite sure about the installation, please do not hesitate to ask for our help.

Before assembly, please check and make sure all necessary accessories are included and undamaged. Improper 

installation, such as use the product for monitors over its load capacity or for any purpose not explicitly specified, 

may cause damage or serious injury. We would not be liable for any damage or injury caused by improper 

mounting or inappropriate use.

The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF REACH OF 

CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.

Stud

Finder

Awl

Wood Drill

ø3/16"(ø4.5mm)

Wood Stud Installation

Hammer

Concrete Installation

Concrete Drill

ø3/8"(ø10mm)

Summary of Contents for MU2001













Reviews: