Motorola T2260 Service Manual Download Page 50

Page: 50 / 121

4/3/01

CDMA 800/1900

73#

PWR-Phase

Programs power phasing values through the handset.

Power phasing depends on the call processing mode. It is

the responsibility of the user to select the proper call

processing mode before using this test command.

This command reprograms the EEPROM phasing values

for Max. Power Level, Attenuator Slope Adjust, etc.

The value in X selects which step to start on. If no value for

X is entered, it will start at step 0.

The command keys are defined in Table 1: “Handset

Command Key Entry” on page 13.

NOTE: If you power down the radio after changes are

made, the power up sequence re-programs the hardware

with the correct phasing values.

Refer to “Tests and Adjustments” on page 47 for instruc-tions

on entering parameters from the keypad.

Analog Power Level Parameters:

RANGE

STEP # POWER LEVEL (HEX)

00 Power Step 0 00-FF

01 Power Step 1 00-FF

02 Power Step 2 00-FF

03 Power Step 3 00-FF

04 Power Step 4 00-FF

05 Power Step 5 00-FF

06 Power Step 6 00-FF

07 Power Step 7 00-FF

08-0B Do Not Adjust

CDMA Power Level Parameters:

RANGE

STEP # POWER LEVEL (HEX)

00 Attenuator Slope Adjust 00-FF

01 Attenuator Offset Adjust 00-FF

02 Clamp Adjust 00-FF

03 VCA Slope Adjust 00-FF

04 VCA Offset Adjust 00-FF

05 PMax 1 (Chan. 991-1023, 1-100) 00-FF

06 PMax 2 (Chan. 101-322) 00-FF

07 PMax 3 (Chan. 323-544) 00-FF

08 PMax 4 (Chan. 545-766) 00-FF

09 PMax 5 (Chan. 767-990) 00-FF

Table 9:

Keypad

Entry

Command

Description

Status

Display

Result

Summary of Contents for T2260


























































































































Search results

Summary of Contents for T2260

Reviews:

Related manuals for T2260

Brands by name

Popular brands

Motorola T2260, Service Manual

Search results

Summary of Contents for T2260

Reviews:

Related manuals for T2260

Brands by name

Popular brands