Motorola Semiconductor MC68HC11F1 Technical Manual Download Page 1 | Manualshive

Page: 1 / 68

background image

Order this document

by MC68HC11FTS/D

© MOTOROLA INC., 1997

This document contains information on a new product. Specifications and information herein are subject to change without notice.

MOTOROLA

SEMICONDUCTOR

TECHNICAL DATA

M

MC68HC11F1

MC68HC11FC0

Technical Summary

8-Bit Microcontroller

1 Introduction

The MC68HC11F1 is a high-performance member of the M68HC11 family of microcontroller units
(MCUs). High-speed expanded systems required the development of this chip with its extra input/output
(I/O) ports, an increase in static RAM (one Kbyte), internal chip-select functions, and a non-multiplexed
bus which reduces the need for external interface logic. The timer, serial I/O, and analog-to-digital (A/
D) converter enable functions similar to those found in the MC68HC11E9.

The MC68HC11FC0 is a low cost, high-speed derivative of the MC68HC11F1. It does not have
EEPROM or an analog-to-digital converter. The MC68HC11FC0 can operate at bus speeds as high as
six MHz.

This document provides a brief overview of the structure, features, control registers, packaging infor-
mation and availability of the MC68HC11F1 and MC68HC11FC0. For detailed information on
M68HC11 subsystems, programming and the instruction set, refer to the

M68HC11 Reference Manual

(M68HC11RM/AD).

1.1 Features

• MC68HC11 CPU
• 512 Bytes of On-Chip Electrically Erasable Programmable ROM (EEPROM) with Block Protect

(MC68HC11F1 only)

• 1024 Bytes of On-Chip RAM (All Saved During Standby)
• Enhanced 16-Bit Timer System

— 3 Input Capture (IC) Functions
— 4 Output Compare (OC) Functions
— 4th IC or 5th OC (Software Selectable)

• On-Board Chip-Selects with Clock Stretching
• Real-Time Interrupt Circuit
• 8-Bit Pulse Accumulator
• Synchronous Serial Peripheral Interface (SPI)
• Asynchronous Nonreturn to Zero (NRZ) Serial Communication Interface (SCI)
• Power saving STOP and WAIT Modes
• Eight-Channel 8-Bit A/D Converter (MC68HC11F1 only)
• Computer Operating Properly (COP) Watchdog System and Clock Monitor
• Bus Speeds of up to 6 MHz for the MC68HC11FC0 and up to 5 MHz for the MC68HC11F1
• 68-Pin PLCC (MC68HC11F1 only), 64-Pin QFP (MC68HC11FC0 only), and 80-pin TQFP pack-

age options

1
2
3
...
»

Summary of Contents for Semiconductor MC68HC11F1





































































Reviews:

No comments

Related manuals for Semiconductor MC68HC11F1

Brand: OmarLift Pages: 14

Brand: Laars Pages: 28

Brand: Velleman Pages: 26

Brand: Velleman Pages: 32

Brand: Velocity Pages: 84

Brand: ABB Pages: 17

Brand: Partizan Pages: 7

SYSMAC C500-NC222-E

Brand: Omron Pages: 164

Brand: Multi-Clean Pages: 4

Brand: Primo Water Pages: 10

Brand: PENGWYN Pages: 32

Brand: Warner Electric Pages: 6

Brand: BQT Pages: 2

Brand: Osaka Pages: 12

Brand: Water Worker Pages: 8

Brand: YASKAWA Pages: 360

Brand: CONCORD Pages: 7

Brand: FOR-A Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands