Motorola PTP 25600 User Manual Download Page 169 | Manualshive

Page: 169 / 237

background image

User Guide: PTP 600 Series

PTP 25600 reference information

phn-0896_009v003

Feb 2010

UNDER DEVELOPMENT

4-21

PTP 25600 available spectrum settings

The supported 2.5GHz frequency range is split into three bands, according to the
bands specified in the FCC BRS-EBS Post-Transition Band plan (only for PTP 25600
and region code 16):

•

Lower: 2496 MHz to 2572 MHz with a 5.5MHz channel raster (76 MHz total).

•

Middle: 2572 MHz to 2614 MHz with a 6 MHz channel raster (42 MHz total).

•

Upper: 2618 MHz to 2690 MHz with a 5.5 MHz channel raster (76 MHz total).

NOTE

For the PTP 25600 product variant, the unit will only operate in Fixed
Frequency mode, and the user is unable to select i-DFS.

The PTP 25600 product variant support channel centre frequencies as specified in

. The 30MHz Channel Bandwidth is not supported in the FCC region.

«
...
167
168
169
170
171
...
»

Summary of Contents for PTP 25600














































































































































































































































Reviews:

No comments

Related manuals for PTP 25600

Brand: 3Com Pages: 8

8 Port 10/100Mbit/s Ethernet Smart Switch with Fibre Uplink

Brand: Tyco Electronics Pages: 18

Brand: Patton electronics Pages: 51

Brand: Delta Tau Pages: 74

Anybus Communicator ABC4021

Brand: HMS Networks Pages: 60

Brand: ebm-papst Pages: 11

EZ-Extender Analog 120-Pin Probing Board

Brand: Analog Devices Pages: 29

Seven Solutions WR-ZEN Series

Brand: Orolia Pages: 167

LinkStation Mini

Brand: Buffalo Pages: 71

Brand: Patton electronics Pages: 13

Brand: Angel Cool Pages: 2

Brand: ZALMAN Pages: 7

Octopus G Series

Brand: TwinMOS Pages: 29

dspstak 21262sx

Brand: Danville Signal Processing Pages: 35

Brand: AirTies Pages: 28

SOUL CALIBUR II

Brand: NAMCO Pages: 26

Brand: TP-Link Pages: 57

Brand: ICOP Technology Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands