Motorola MC68VZ328 User Manual Download Page 276 | Manualshive

Page: 276 / 376

background image

14-24

MC68VZ328 User’s Manual

Programming Model

14.4.11

UART 2 Transmitter Register

The UART 2 transmitter (UTX2) register controls how the transmitter operates. The bit position
assignments for this register are shown in the following register display. The settings for this register are
described in Table 14-13.

UTX2

UART 2 Transmitter Register

0x(FF)FFF916

FRAME
ERROR
Bit 10

Frame Error (Character Status)—This read-only bit indicates
that the current character had a framing error (missing stop bit),
which indicates that there may be corrupted data. This bit is
updated for each character read from the FIFO.

0 = Character has no framing error
1 = Character has a framing error

BREAK
Bit 9

Break (Character Status)—This read-only bit indicates that
the current character was detected as a BREAK. The data bits
are all 0 and the stop bit is also 0. The FRAME ERROR bit will
always be set when this bit is set, and if odd parity is selected,
PARITY ERROR will also be set. This bit is updated and valid
with each character read from the FIFO.

0 = Character is not a break

character

1 = Character is a break character

PARITY
ERROR
Bit 8

Parity Error (Character Status)—This read-only bit indicates
that the current character was detected with a parity error,
which indicates that there may be corrupted data. This bit is
updated and valid with each character read from the FIFO.
While parity is disabled, this bit always reads 0.

See description

RX
DATA
Bits 7–0

Rx Data (Character Data)—This read-only field is the top
receive character in the FIFO. The bits have no meaning if the
DATA READY bit is 0. In 7-bit mode, the most significant bit is
forced to 0, and in 8-bit mode, all bits are active.

See description

BIT 15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

BIT 0

FIFO

EMPTY

FIFO

HALF

TX

AVAIL

SEND

BREAK

NO

CTS2

B
U
S
Y

CTS2
STAT

CTS2

DELTA

TX DATA

TYPE

r

r

r

rw

rw

rw

rw

rw

w

w

w

w

w

w

w

w

RESET

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0x0000

Table 14-13. UART 2 Transmitter Register Description

Name

Description

Setting

FIFO
EMPTY
Bit 15

FIFO Empty (FIFO Status)—This read-only bit indicates that
the transmitter FIFO is empty. This bit generates a maskable
interrupt.

0 = Transmitter FIFO is not empty
1 = Transmitter FIFO is empty

Table 14-12. UART 2 Receiver Register Description (Continued)

Name

Description

Setting

«
...
274
275
276
277
278
...
»

Summary of Contents for MC68VZ328

























































































































































































































































































































































































Reviews:

No comments

Related manuals for MC68VZ328

Brand: Palo Alto Network Pages: 56

COMSPHERE 3800 Series

Brand: Paradyne Pages: 88

COMSPHERE 3800PLUS

Brand: Paradyne Pages: 5

Brand: NXP Semiconductors Pages: 24

PCI-6110E/6111E

Brand: National Instruments Pages: 113

Brand: Tait Pages: 8

Brand: C4i Pages: 5

Brand: SeaLevel Pages: 21

Industrial Network Track OSI

Brand: GarrettCom Pages: 10

2410SA - Serial ATA RAID Controller

Brand: Adaptec Pages: 14

DAS-1800HR Series

Brand: Keithley Pages: 139

Brand: Adaptec Pages: 2

ST7-EMU3 Series

Brand: ST Pages: 39

55PUS8118 SCSI-2

Brand: IBM Pages: 42

Brand: Icop Pages: 31

Brand: Edimax Pages: 14

Brand: VIA Technologies Pages: 14

Brand: VIA Technologies Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands