manualshive.com logo in svg

Motorola E815, Service Manual, Page: 34 / 48

Share
Download
Motorola E815 Service Manual Download Page 34

34

   January 24, 2006 

6809492A18-B

Disassembly

 E815, E816 CDMA

Removing the Motor/Vibrator Assembly

1.

Remove the battery cover, battery, antenna, keypad bezel, speaker cover, 
keyboard stiffener, keypad flex, flip flex connector, transceiver board, flip 
assembly, flip display lens, flip sleeve, flip display bezel, display module 
assembly as described in the procedures.

2.

Use the flat edge of the disassembly tool to remove the motor/vibrator assembly 
from the flip housing (see Figure 22).

3.

To replace, align the motor/vibrator assembly to its place in the flip housing 
assembly. 

4.

Carefully press the motor/vibrator assembly into position in the flip housing. 
Ensure that the motor/vibrator assembly is fully seated and the surface of the 
motor/vibrator assembly is flush with the outer plane of the flip housing. 
Ensure the motor/vibrator shaft turns freely.

5.

Replace the display assembly, display bezel, flip knuckle, flip assembly sleeve, 
flip assembly, flip display lens, transceiver board, flip assembly, keyboard 
stiffener, speaker cover, keypad bezel, antenna, battery, and battery cover as 
described in the procedures.

032232o

Figure 22. Removing the Motor/Vibrator Assembly 

Motor/Vibrator Assembly

Flip Housing Assembly

Disassembly Tool

Summary of Contents for E815

















































Reviews:

No comments