Motorola E815 Service Manual Download Page 32 | Manualshive

Page: 32 / 48

Motorola E815 Service Manual Download Page 32

32

January 24, 2006

6809492A18-B

Disassembly

E815, E816 CDMA

Removing and Replacing the Camera Module

1.

Remove the battery cover, battery, antenna, keypad bezel, speaker cover,
keyboard stiffener, flip assembly, transceiver board, flip display lens, flip
assembly, flip assembly sleeve, flip knuckle, display bezel, and display assem-
bly as described in the procedures.

2.

Use the disassembly too to unseat the camera module connector from its socket
on the display assembly (see Figure 20).

3.

Carefully lift the camera module away from the display assembly.

4.

To replace, align the camera module connector to its socket on the display
assembly.

5.

Carefully but firmly press the connector into the socket until properly seated.

6.

Replace the display assembly, display bezel, flip knuckle, flip assembly sleeve,
flip assembly, flip display lens, transceiver board, flip assembly, keyboard
stiffener, speaker cover, keypad bezel, antenna, battery, and battery cover as
described in the procedures.

050286o

Figure 20. Removing the Camera Module

Display Assembly

Camera Connector

Disassembly Tool

Camera Module

«
...
30
31
32
33
34
...
»

Summary of Contents for E815

















































Reviews:

No comments