Motorola DSP56309 User Manual Download Page 259 | Manualshive

Page: 259 / 425

background image

9-18

DSP56309UM/D MOTOROLA

Triple Timer Module

Timer Operational Modes

is reloaded with the TLR value at the next timer clock and the count is resumed. If the
TRM bit is cleared, the counter continues to be incremented on each timer clock signal.

This process is repeated until the timer is disabled (i.e., TE is cleared).

If the counter overflows, the TOF bit is set, and if TOIE is set, an overflow interrupt is
generated.

The counter contents can be read at any time by reading the TCR.

9.4.1.2

Timer Pulse (Mode 1)

In this mode, the timer generates an external pulse on its TIO signal when the timer
count reaches a pre-set value.

Set the TE bit to clear the counter and enable the timer. The value to which the timer is to
count is loaded into the TCPR. The counter is loaded with the TLR value when the first
timer clock signal is received. The TIO signal is loaded with the value of the INV bit. The
timer clock signal can be taken from either the DSP56309 clock divided by two (CLK/2)
or from the prescaler clock output. Each subsequent clock signal increments the counter.

When the counter matches the TCPR value, the TCF bit in TCSR is set and a compare
interrupt is generated if the TCIE bit is set. The polarity of the TIO signal is inverted for
one timer clock period.

If the TRM bit is set, the counter is loaded with the TLR value on the next timer clock and
the count is resumed. If the TRM bit is cleared, the counter continues to be incremented
on each timer clock.

This process is repeated until the TE bit is cleared (disabling the timer). The counter
contents can be read at any time by reading TCR.

The value of the TLR sets the delay between starting the timer and the generation of the
output pulse. To generate successive output pulses with a delay of X clocks between
signals, the TLR value should be set to X/2 and the TRM bit should be set.

This process is repeated until the timer is disabled (i.e., TE is cleared).

Bit Settings

Mode Characteristics

TC3

TC2

TC1

TC0

TIO

Clock

#

Function

Name

0

0

0

1

Output

Internal

1

Timer

Pulse

«
...
257
258
259
260
261
...
»

Summary of Contents for DSP56309










































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DSP56309

Brand: Scarlett Pages: 36

Brand: Exido Pages: 32

Brand: Vitek Pages: 4

Brand: Johnson Pages: 36

Brand: Zelmer Pages: 94

Stack & Snap 70820

Brand: Hamilton Beach Pages: 36

Brand: Hyundai Pages: 56

Brand: Black & Decker Pages: 3

Brand: Black & Decker Pages: 25

Brand: Black & Decker Pages: 24

Brand: Black & Decker Pages: 56

PrecisionPower DCX 730

Brand: Precision Power Pages: 13

Brand: PhatNoise Pages: 2

Brand: Babybrezza Pages: 4

Brand: Babybrezza Pages: 4

Brand: Philips Pages: 8

Brand: Wolf Garten Pages: 90

Brand: ARIETE Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands