manualshive.com logo in svg

Motorola DS9808 - Symbol - Wired Handheld Barcode Scanner, Product Reference Manual

Introducing the Motorola DS9808 - Symbol - Wired Handheld Barcode Scanner! Enhance your business operations with this advanced scanner, offering unmatched efficiency and accuracy. To get started quickly, simply download the free Quick Start Manual from manualshive.com. Experience seamless scanning and effortless productivity with this innovative device.

Share
Download
background image

3 - 2

Symbol DS9808 Product Reference Guide

Troubleshooting

Table 3-1    

Troubleshooting

Problem

Possible Causes

Possible Solutions

The aiming pattern does not 
appear when pressing the 
trigger.

No power to the digital scanner.

If the configuration requires a power 
supply, re-connect the power supply.

Incorrect host interface cable is used. 

Connect the correct host interface 
cable. 

Interface/power cables are loose.

Re-connect cables.

Digital scanner is disabled.

For IBM 468x and USB IBM hand-held, 
IBM table top, and OPOS modes, 
enable the digital scanner via the host 
interface. Otherwise, see the technical 
person in charge of scanning.

If using RS-232 Nixdorf B mode, CTS 
is not asserted.

Assert CTS line. 

Aiming pattern is disabled.

Enable the aiming pattern. See 

Hand-Held Decode Aiming Pattern on 
page 4-34

. 

Digital scanner emits short 
low/short medium/short high 
beep sequence (power-up beep 
sequence) more than once.

The USB bus may put the digital 
scanner in a state where power to the 
scanner is cycled on and off more than 
once.

Normal during host reset.

Digital scanner emits aiming 
pattern, but does not decode the 
bar code.

Digital scanner is not programmed for 
the correct bar code type.

Program the digital scanner to read that 
type of bar code. See 

Chapter 11, 

Symbologies

.

Bar code symbol is unreadable.

Scan test symbols of the same bar 
code type to determine if the bar code 
is defaced.

The symbol is not completely inside 
aiming pattern.

Move the symbol completely within the 
aiming pattern.

Digital scanner emits 4 short 
high beeps during decode 
attempt.

Digital scanner has not completed 
USB initialization.

Wait several seconds and scan again.

Summary of Contents for DS9808 - Symbol - Wired Handheld Barcode Scanner

































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DS9808 - Symbol - Wired Handheld Barcode Scanner

Raymarine RCR-1 Installation Instructions Manual preview
RCR-1
Brand: Raymarine Pages: 46
Hamlet HBCS2D100US User Manual preview
HBCS2D100US
Brand: Hamlet Pages: 58
Wasp WDI4700 Quick Reference Manual preview
WDI4700
Brand: Wasp Pages: 48
Metrologic MH941 Installation And User Manual preview
MH941
Brand: Metrologic Pages: 33
C Prox Quntek PN10 User Manual preview
Quntek PN10
Brand: C Prox Pages: 7
Element P130BT User Manual preview
P130BT
Brand: Element Pages: 120
Datalogic Magellan 800i Reference Manual preview
Magellan 800i
Brand: Datalogic Pages: 184
Aritech ATS1190 Installation Sheet preview
ATS1190
Brand: Aritech Pages: 22
Infinite Peripherals Linea Pro 7 User Manual preview
Linea Pro 7
Brand: Infinite Peripherals Pages: 31
Unitech MS860 Bluetooth Specifications preview
MS860 Bluetooth
Brand: Unitech Pages: 2
Unitech MS852LR Quick Start Manual preview
MS852LR
Brand: Unitech Pages: 2
Unitech MS852 Auto Switching Quick Start Manual preview
MS852 Auto Switching
Brand: Unitech Pages: 2
Unitech RG630 Quick Start Manual preview
RG630
Brand: Unitech Pages: 2
Unitech MS912+ User Manual preview
MS912+
Brand: Unitech Pages: 91
Technology Solutions 1166 User Manual preview
1166
Brand: Technology Solutions Pages: 31
Baracoda Barcode Reader User Manual preview
Barcode Reader
Brand: Baracoda Pages: 25
Nordic ID sampo Quick Manual preview
sampo
Brand: Nordic ID Pages: 12
Nordic ID EXA51E User Manual preview
EXA51E
Brand: Nordic ID Pages: 35

Brands by name

Popular brands

Load more brands