manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

 

Chapter 21.  IEEE 1149.1 Test Access Port (JTAG)

 

  

21-7

 

Instruction Register

 

Figure 21-7. General Arrangement for Bidirectional Pins

 

21.5  Instruction Register

 

The MCF5272 IEEE 1149.1 implementation includes the three mandatory public
instructions (EXTEST, SAMPLE/PRELOAD, and BYPASS), the optional public ID
instruction, plus two additional public instructions (CLAMP and HI-Z) defined by IEEE
1149.1. The MCF5272 includes a 4-bit instruction register without parity, consisting of a
shift register with four parallel outputs. Data is transferred from the shift register to the
parallel outputs during the update-IR controller state. The 4 bits are used to decode the
instructions in Table 21-2.

The parallel output of the instruction register is reset to 0001 in the test-logic-reset
controller state. Note that this preset state is equivalent to the ID instruction.

 

Table 21-2. Instructions 

 

B[3:0]

Instruction

Description

 

0000

EXTEST

The external test (EXTEST) instruction selects the boundary scan register. EXTEST asserts 
internal reset for the MCF5272 system logic to force a predictable benign internal state while 
performing external boundary scan operations. 
By using the TAP, the register is capable of a) scanning user-defined values into the output 
buffers, b) capturing values presented to input pins, c) controlling the direction of bidirectional 
pins, and d) controlling the output drive of three-state output pins. For more details on the 
function and uses of EXTEST, please refer to the IEEE 1149.1 document.

0001

ID

During the capture-IR controller state, the parallel inputs to the instruction shift register are 
loaded with the 4-bit binary value (0001). The parallel outputs, however, remain unchanged 
by this action since an update-IR signal is required to modify them.

IO.CELL

FROM LAST CELL

OUTPUT

DATA  

INPUT

 DATA   

OUTPUT

ENABLE

I/O

PIN

TO NEXT CELL

*

NOTE:  More than one lO.Cell could be serially connected and controlled by a single En.Cell.

EN.CELL

*

DIRECTION

OUTPUT
ENABLE

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

Rabbit 2000 Designers Handbook preview
2000
Brand: Rabbit Pages: 45
Rabbit 2000 Instruction & Reference Manual preview
2000
Brand: Rabbit Pages: 174
Rabbit 2000 Getting Started preview
2000
Brand: Rabbit Pages: 43
Barco EX Safety Manual preview
EX
Brand: Barco Pages: 100
IEI Technology PCIE-Q470 Quick Installation Manual preview
PCIE-Q470
Brand: IEI Technology Pages: 19
IEI Technology KINO-DH420 User Manual preview
KINO-DH420
Brand: IEI Technology Pages: 87
IEI Technology HPE-4S2 Quick Installation Manual preview
HPE-4S2
Brand: IEI Technology Pages: 3
Profile LS901-E1 Instruction Manual preview
LS901-E1
Brand: Profile Pages: 6
SUNRICH TECHNOLOGY C-330 User Manual preview
C-330
Brand: SUNRICH TECHNOLOGY Pages: 5
peplink balance ONE Manual preview
balance ONE
Brand: peplink Pages: 2
Giacomini KPM36Y002 Manual preview
KPM36Y002
Brand: Giacomini Pages: 2
ICP DAS USA iWSN-200E Quick Start Manual preview
iWSN-200E
Brand: ICP DAS USA Pages: 8
Penguin Edge MVME2500 Quick Start Manual preview
MVME2500
Brand: Penguin Edge Pages: 2
Lattice Semiconductor sysCLOCK ECP5 Usage Manual preview
sysCLOCK ECP5
Brand: Lattice Semiconductor Pages: 43
Paradyne ACCULINK 3161 CSU Quick Reference Manual preview
ACCULINK 3161 CSU
Brand: Paradyne Pages: 19
Sony Ericsson Developer's Board Manual preview
Developer's Board
Brand: Sony Ericsson Pages: 28
Xinje VH5 Series User Manual preview
VH5 Series
Brand: Xinje Pages: 76
Juniper WX 100 Quick Start Manual preview
WX 100
Brand: Juniper Pages: 6

Brands by name

Popular brands

Load more brands