Motorola DigitalDNA ColdFire MCF5272 User Manual Download Page 217 | Manualshive

Page: 217 / 550

background image

Chapter 10. DMA Controller

10-3

DMA Controller Registers

Table 10-2. DMR Field Descriptions

Bits

Name

Description

31

RESET

Reset. Writing a 1 to this location causes the DMA controller to reset to a condition where no
transfers are taking place. EN is cleared, preventing new transfers.

30

EN

Enable. Controls whether the DMA channel is enabled to perform transfers.
0 DMA transfers are disabled.
1 DMA transfers are enabled. The DMA controller can respond to requests from the peripheral or

generates internal requests in dual address mode, so long as the conditions described under
the DMA interrupt flags (see Section 10.3.2, “DMA Interrupt Register (DIR)”) do not prevent
transfers from going ahead.

29–20

—

Reserved, should be cleared.

19–18

RQM

Request mode. Determines the request mode of the channel. This must be 11.
00–10 Reserved, do not use.
11 Dual address request mode. Both the DMA source and DMA destination are memory

addresses. The MCF5272 supports only dual-address request mode.

17–15

—

Reserved, should be cleared.

14–13

DSTM

Destination addressing mode for the channel.
00 Static address mode
01 Increment address mode
1x Reserved, do not use.

12–10

DSTT

Destination addressing type. Used internal to the MCF5272 to qualify the address bits. This value
should be compatible with the CSCRn[TM] value used for external RAM or peripheral device
access.
000 Reserved
001 User data access
010 User code access
011–100 Reserved
101 Supervisor data access
110 Supervisor code access
111 Reserved

9–8

DSTS

Destination data transfer type. The DMA controller buffers data from the source address data
fetches until there are enough bytes to perform a destination data write of the size programmed in
these bits. Thus it is possible to configure source accesses to be byte type and destination
addresses to be line burst type. In this case 16 individual byte reads are performed followed by an
indivisible burst write of four longwords. Longword or line bursts are the most efficient data
transfers.

DSTS

Data Transfer Type

Address Incremented by

00

Longword

4

01

Byte 1

10

Word

2

11

16-byte line burst

16. Valid only for SDRAM.

7

—

Reserved, should be cleared.

6

—

Reserved, should be cleared.

5

SRCM

Source addressing mode of the channel.
0

Static address mode

1

Increment address mode

«
...
215
216
217
218
219
...
»

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

Brand: Opengear Pages: 2

Brand: Alacritech Pages: 20

eXtremeRAID 1100

Brand: Mylex Pages: 74

Brand: Supermicro Pages: 16

SteelCentral NetExpress

Brand: Riverbed Pages: 38

FireWire 800 + Hi-Speed USB Combo

Brand: SIIG Pages: 20

Brand: Altera Pages: 42

Brand: Paradyne Pages: 10

Brand: H3C Pages: 3

Brand: IBASE Technology Pages: 39

Oresund EFC102200

Brand: Bridgeworks Pages: 84

Brand: Lattice Semiconductor Pages: 43

ACCULINK 3161 CSU

Brand: Paradyne Pages: 19

Brand: ICOP Technology Pages: 42

Brand: Cypress Semiconductor Pages: 31

Brand: Uctronics Pages: 12

Brand: LevelOne Pages: 142

Brand: Thecus Pages: 148

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands