manualshive.com logo in svg

Motorola DigitalDNA ColdFire MCF5272, User Manual

The user manual for the high-performance Motorola DigitalDNA ColdFire MCF5272 can be easily downloaded for free from our website. This comprehensive manual provides step-by-step instructions and detailed information on operating this advanced product. Unlock the full potential of your MCF5272 through our hassle-free online manual download.

Share
Download
background image

Chapter 8.  Chip Select Module  

8-3

Chip Select Registers

8.2.1  Chip Select Base Registers (CSBR0–CSBR7)

The CSBRs, Figure 8-1, provide a model internal bus cycle against which to match actual
bus cycles to determine whether a specific chip select should assert. A bus cycle in a specific
chip select register causes the assertion of the corresponding external chip select.

Table 8-2 describes CSBRn fields. 

31

12 11

10

9

8

7

6

5

4

2

1

0

Field

BA

EBI

BW

SUPER

TT

TM

CTM ENABLE

Reset

CSBR0: 0x0000_0x01

1

; CSBR1: 0x0000_1300; CSBR2: 0x0000_2300; CSBR3: 0x0000_3300; 

CSBR4: 0x0000_4300; CSBR5: 0x0000_5300; CSBR6: 0x0000_6300; CSBR7: 0x0000_7700

R/W

R/W

Addr

0x040 (CSBR0); 0x048 (CSBR1); 0x050 (CSBR2); 0x058 (CSBR3); 

0x060 (CSBR4); 0x068 (CSBR5); 0x070 (CSBR6); 0x078 (CSBR7)

Figure 8-1. Chip Select Base Registers (CSBRn)

Table 8-2. CSBRn Field Descriptions 

Bits

Name

Description

31–12

BA

Base address. The starting address of the memory space covered by the chip select. BA is 
compared with bits 31–12 of the access to determine whether the current bus cycle is intended 
for this chip select. Any combination of BA bits can be masked in the associated CSOR.

11–10

EBI

External bus interface modes. These modes are used to multiplex outputs and determine timing 
of the appropriate bus interface module onto the device pins.
00 16-/32-bit SRAM/ROM. For 16-/32-bit wide memory devices with byte strobe inputs. 

CSBR0[EBI] = 00 at reset. Affects all chip selects. 

01 SDRAM. One physical bank of SDRAM consisting of 16–256 Mbit devices. CSOR7[WS] must 

be set to 0x1F. Affects only CS7/SDCS.

10 Reserved
11 Use SRAM/ROM timing for 8-bit devices without byte strobe inputs. 

9–8

BW

Bus width. Determines data bus size of the memory-mapped resource for all chip selects except 
CS0. It is assumed that boot code for the processor is accessed through the global chip select 
CS0, so the initial bus width for this chip select must be configured at reset. QSPI_CS0/BUSW0 
and QSPI_CLK/BUSW1 are used to program the bus width for CS0 at reset.
00 Longword (32 bits)
01 Byte (8 bits)
10 Word (16 bits)
11 Cache line (32 bits)

7

SUPER

Supervisor mode. 
0 Bus cycle may be in user or supervisor mode (neglecting conditions imposed by setting CTM).
1 The chip select asserts a match only if the transfer modifier indicates a supervisor mode 

access. A user access matching BA causes an access error. 

SUPER, CTM, TT, and TM are used to restrict bus access. For example, if TT and TM indicate a 
user data access and SUPER and CTM are both set, no accesses can occur.

6–5

TT

Transfer type. TT and TM may be used to further qualify the address match. If CTM is set, TT and 
TM must match the access types for the chip select to assert. See the description of TM. 

Summary of Contents for DigitalDNA ColdFire MCF5272







































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DigitalDNA ColdFire MCF5272

NAIM AV2 Update Instructions preview
AV2
Brand: NAIM Pages: 2
RadiSys EPC-31 Hardware Reference Manual preview
EPC-31
Brand: RadiSys Pages: 44
LGC wireless InterReach Fusion SingleStar Installation And Operation Manual preview
InterReach Fusion SingleStar
Brand: LGC wireless Pages: 154
Dust Networks SmartMesh IA-510 D2511 Manager'S Manual preview
SmartMesh IA-510 D2511
Brand: Dust Networks Pages: 30
C-Com IPAM-1600s Series User Manual preview
IPAM-1600s Series
Brand: C-Com Pages: 148
Doremi MB-4K User Manual preview
MB-4K
Brand: Doremi Pages: 15
Echo LAYLA 3G Owner'S Manual preview
LAYLA 3G
Brand: Echo Pages: 21
JAKA MiniCab Hardware User Manual preview
MiniCab
Brand: JAKA Pages: 37
Renesas H8S/2646 Series User Manual preview
H8S/2646 Series
Brand: Renesas Pages: 20
Buffalo AirStation G54 WLA2-G54 Quick Setup Manual preview
AirStation G54 WLA2-G54
Brand: Buffalo Pages: 8
National Semiconductor Data Capture Board CLC-CAPT-PCASM User Manual preview
Data Capture Board CLC-CAPT-PCASM
Brand: National Semiconductor Pages: 15
Genexis FiberTwist XGS2420 Installation Manual preview
FiberTwist XGS2420
Brand: Genexis Pages: 7
ADLINK Technology cPCI-3520 Series User Manual preview
cPCI-3520 Series
Brand: ADLINK Technology Pages: 81
X-Micro XWL-11GPAR User Manual preview
XWL-11GPAR
Brand: X-Micro Pages: 24
Ecos SECURE BOOT STICK FX Administrator'S Manual preview
SECURE BOOT STICK FX
Brand: Ecos Pages: 22
Extron electronics DMP 64 Plus User Manual preview
DMP 64 Plus
Brand: Extron electronics Pages: 99
Whirlwind PYROBOX Technical Specifications preview
PYROBOX
Brand: Whirlwind Pages: 1
Arista CCA-ETM-Q8W Quick Start Manual preview
CCA-ETM-Q8W
Brand: Arista Pages: 22

Brands by name

Popular brands

Load more brands