manualshive.com logo in svg

Motorola A840 - Cell Phone - CDMA2000 1X, Service Manual, Page: 34 / 56

Share
Download
Motorola A840 - Cell Phone - CDMA2000 1X Service Manual Download Page 34

36

   June 07, 2004   

6809485A78-O

Disassembly

 A840

5.

Lift the keyboard stiffener away from the phone.

6.

To replace, align the keyboard stiffener to the transceiver board.

7.

Connect the keyboard flex connector to its socket on the transceiver board.

8.

Lower the keyboard stiffener onto the transceiver board.

9.

Insert and tighten two screws near the polyphonic speaker assembly.

10. Replace the speaker cover, keypad bezel, antenna, battery, and battery cover 

as described in the procedures. 

Removing and Replacing the Flip Assembly and Transceiver Board

1.

Remove the battery cover, battery, antenna, keypad bezel, speaker cover, and 
keyboard stiffener as described in the procedures.

2.

Use the disassembly tool to disconnect the flip assembly flex connector. (See 
Figure 17).

032216o

Figure 17. Removing the Flip Assembly Flex Connector

Flip Flex 

Connector

disassembly tool

Summary of Contents for A840 - Cell Phone - CDMA2000 1X

























































Reviews:

No comments